Comentarios de Clientes

4.77 fuera de 5
Escribe un Comentario
  • Todos los comentarios (84)
  • Imagen (7)
  • Video (0)
  • Todas Las Estrellas
    • Todas Las Estrellas(84)
    • 5 Estrellas(70)
    • 4 Estrellas(11)
    • 3 Estrellas(2)
    • 2 Estrellas(0)
    • 1 Estrellas(1)
Ordenar por:
Comentarios Recomendados
  • Comentarios Recomendados
  • Muy útil
  • Más Reciente
Reseñas solo de tu país (Honduras)
Mostrar original

Una parte de la reseña se ha traducido automáticamente.

  • 23/10/2018

    The package was well protected at the factory. But, when I opened it carefully, I found that one z-axis slide rod was missing as shown circled on the first picture. Informed Banggood customer service of this missing item. After a few emails back and forth with Banggood customer service, they were able to resolve the issue by sending me a replacement z-axis slide rod. I have since received the replacement slide rod (see picture 2) and have quickly completed the assembly of the machine (see picture 3). Tested the machine and electronics to work perfectly. All in all, I was happy and satisfied with the customer service at Banggood in resolving the stated issue. The machine is nice and compact, but most of all, I liked the price. I know I will have many hours of enjoying with this machine.

    Mostrar original
  • 10/09/2018

    I’m an engineer that works projecting and assembly prototypes and consider myself a person with experience assembling machines and some knowledge in electronics hardware and software. it took me 6h to assembly it all and 2h to calibrate it properly. the result surprised me its a nice machine especially for this price! some 3D printed parts turns it difficult to assembly one came bent the one with linear bearings seems to have the holes where you mount the bearings misaligned and the screwed shaft terminals needed to enlarge its holes to fit the shaft. The bolts you use to tight the motor coupling to the shaft are poor quality and its hard to pull off the tool after screw. The board is good aluminium structure is very solid and robust

    Mostrar original
  • 17/05/2018

    product Quality is Perfect but the main problem is about the software need to find some good software ... i have use led strip lights under the driller looks amazing i can see my work area so clear 😃

    Mostrar original
  • 06/04/2019

    All packed fine. Motors have scratches at back side. Looks like be in used. Mators:D42HSC1413B-24. Power adapter light weight. Cable of power adapter, looks cheap. Conners for main frame some kind of metal. Controller board from back not clean. Has remnants flux

    Mostrar original
  • STPL

    Good quality, easy to assemble mechanical parts, Screw driver should be provided along with the machine. Guide should be in proper English and updated, We have used our expert fitter to assemble it Configuration of machine was not correct, axis movement inverted. Hard Board should be provided free of cost along with all machine Better quality of drill bits should be supplied, Overall it is value for money

    Mostrar original
  • 30/03/2019

    It's nice, but only 2 cutting tool is provided and the product dimension are not accurate.

    Mostrar original
  • 15/10/2018

    Estoy feliz de recibir este articulo que compre en Banggood, mi lugar favorito de compras en lineas

    Mostrar original
  • 14/02/2018

    Two half day is needed to build the machine. I met problem with a smaller ball bearing (on Z axis) which loses its balls ... Control board is different from description (MKS DLC V1.0) with last GRBLversion ( V1.1) but seems better. GRBL parameters to use for $100 to $102 are 780 and for $6 is 5. I tried different milling setup: my best setup for PCB is : zwork=-0.1 mm / milling speed = 20000 rpm / milling feed is 120 mm/min

    Comentarios (2)
    Mostrar original
  • 04/01/2018

    The assembly of the machine was relatively easy. But I also consider IKEA furiture easy to build :-). I havent used the T-nuts provided in the package but used bigger ones instead, see The Z-axix comes out of a 3D-printer, which is surprisingly sturdy. However, the little spax are very brittle, I turned the head of two of them, the holes seem to be too tight so the thread scuffs the screw. This means, I need a new part. Be careful not to over tighten the screws. I also will alter this design later to allow easy tool changes, i.g. from a spindle to a laser head or pen for plotting. The controller is preflashed with grbl 0.8c and works with the grblController software provided. In case you want to upgrade the grbl software running in the Arduino Nano, the following settings need to be altered to accommodate the different layout of this special CNC shield. I found the following works correctly for CPU_MAP_ATMEGA328P. This setting is working for the CNC shield of the CNC2417 see config.h for grbl version <= 0.8 see cpu_map.h for grbl version >= 1.1 (0.9 I haven't checked :-) ) #define X_STEP_BIT 3 // Nano Digital Pin 3 #define Y_STEP_BIT 5 // Nano Digital Pin 5 #define Z_STEP_BIT 7 // Nano Digital Pin 7 #define X_DIRECTION_BIT 2 // Nano Digital Pin 2 #define Y_DIRECTION_BIT 4 // Nano Digital Pin 4 #define Z_DIRECTION_BIT 6 // Nano Digital Pin 6 Search for "#ifdef CPU_MAP_ATMEGA328P " in the file according to your version and in the section you will find the 6 entries to modify. Once compiled and uploaded, you also can use Candela to control the machine Happy engraving, Ralph.

    Comentarios (3)
    Mostrar original
  • 07/11/2018

    Very easy to assemble if they pay more attention to production control. Some holes were drilled small, others larger than they should be. But it could be fixed. And the assembly instructions are different. I felt like some photos would have been overturned. Once everything has worked, it works as it does.

    Mostrar original

    Total 0 paginas

    Ir a la pagina

    Puedes estar interesado

    recommendation for you
    • US$305.99
    • US$269.99
    • US$217.99
    • US$330.99
    • US$133.71
    • US$10.99
    • US$403.99
    • US$6.99
    • US$199.99
    • US$272.99
    • US$298.99
    • US$253.99
    • US$260.99
    • US$399.99
    • US$222.99
    • US$16.99