Comentarios de Clientes

4.9 fuera de 5
Ver todos 113 comentarios
Escribe un Comentario
  • Todos los comentarios (113)
  • Imagen (8)
  • Video (1)
  • Todas Las Estrellas
    • Todas Las Estrellas(113)
    • 5 Estrellas(107)
    • 4 Estrellas(4)
    • 3 Estrellas(0)
    • 2 Estrellas(1)
    • 1 Estrellas(1)
Ordenar por:
Comentarios Recomendados
  • Comentarios Recomendados
  • Muy útil
  • Más Reciente
Reseñas solo de tu país (Spain)
|
Mostrar original

Una parte de la reseña se ha traducido automáticamente.

  • 12/09/2017

    In meiner kleinen Wetterstation habe ich einen ESP8266 verbaut. Das Arduino-kompatible Modul führt die Verbindung zu meinem WLAN durch. Bisher funktioniert das ausgezeichnet. Ich werde einie weiter Experiment mit diesem preiswerten Modul machen. Mein Video mit der Arbeitsweise der Wetterstation habe ich hier: https://youtu.be/DSEfxub_-f4 -------------------------------------------------------- In my small weather station I have an ESP8266 installed. The Arduino-compatible module connects to my WLAN. So far, this works very well. I'm going to make a next experiment with this cheap module. My video with the operation of the weather station I have here: https://youtu.be/DSEfxub_-f4

    Comentarios
    Mostrar original
  • 21/10/2016

    Although these modules are shipped with the NodeMcu firmware installed, it's very easy to load your own firmware using the Arduino IDE. There are loads of websites detailing installing the ESP8266 Boards Manager (Google) and, once installed, you write code in the normal Arduino IDE and upload it directly into the ESP8266 module without using the Arduino (Uno, mega, whatever) at all. The ESP8266 *replaces* the Arduino hardware. Sketches are written exactly as for the Arduino, the only point to note is that, in common with most ESP8266 development boards, the pin numbers written on the silk screen are NOT the numbers to use in your sketches. You need to use the actual "GPIO" pin numbers of the ESP8266 chip itself - Google ESP82266-12E pinout. The attached photo shows the ESP8266 module being put through its paces. Measuring temperature with a DS18b20, measuring pressure and temperature with a BMP180 module and lighting two LEDS. At the same time, the ESP8266 module is connected by WiFi to my router and I'm able to display the sensor measurements and control the two LEDS via a simple webpage created by the onboard Arduino-style sketch.

    Comentarios
    Mostrar original
  • 16/01/2018

    THIS PRODUCT I RECEIVE AS DESCRIBED AND I GET 3 PCS OF NODEMCU ESP 8266 AND ITS AMAZING EXPERIENCE AND GRATE SHIPPING AND FASTER REACH ME . THANKS A LOT BANGGOOD PROVIDE AMAZING SHIPPING AND PRODUCT AUTHENTICATE ..

    Comentarios
    Mostrar original
  • krbVIP1
    GB
    15/01/2018

    I love these little things came faster than expected! exactly 2 weeks after placing order. one came without Lua firmware but that's not an issue. have been using one of these for months and hasn't failed on me so I got 3 more

    Comentarios
    Mostrar original
  • 04/02/2018

    Funziona bene e non mi ha dato problemi in nessuna delle mie applicazioni. Solo ogni tanto negli usi più pesanti si blocca, ma basta un riavvio.

    Comentarios
    Mostrar original
  • 13/09/2017

    Пришли 3 штуки как и заказывал. В работе не проверял еще выглядят добротно

    Comentarios
    Mostrar original
  • 23/11/2017

    The product looks good. havent tested it out yet. thanks banggood!

    Comentarios
    Mostrar original
  • icelit
    CL
    04/10/2017

    Works perfectly

    Comentarios
    Mostrar original
  • 24/03/2019

    Received in good condition. It did not work. So I started search. Finally found it. 1. Download and install CP210x USB to UART bridge 2. follow https://randomnerdtutorials.com/installing-the-esp32-board-in-arduino-ide-windows-instructions/ 3.Had uploading issue.I have to hold down the reset but after esptool starts to try to send for about a second or two and then release and it loads. All my other boards load with no hand holding. Hope that is what the problem is. Now it is working. Too wide for the standard bread board.

    Comentarios
    Mostrar original
  • 12/09/2017

    Esp 12 E do not start running with external supply. It starts ONLY after pushing RESET knob on the card. External supply is connected to Vin and GND. Starts well (without any manual RESET), if power comes from its own USB connector.

    Comentarios
    Mostrar original
Show:

    Total 0 paginas

    Ir a la pagina

    Puedes estar interesado

    recommendation for you
    • US$6.99
    • US$4.99
    • US$3.99
    • US$23.09
    • US$4.59
    • US$8.04
    • US$22.99
    • US$4.99
    • US$6.99
    • US$4.09
    • US$9.99
    • US$6.99
    • US$8.99
    • US$29.99
    • US$7.99
    • US$29.99
    • US$16.99
    • US$42.54