Comentarios de Clientes

4.93 fuera de 5
Escribe un Comentario
  • Todos los comentarios (29)
  • Imagen (4)
  • Video (0)
  • Todas Las Estrellas
    • Todas Las Estrellas(29)
    • 5 Estrellas(27)
    • 4 Estrellas(2)
    • 3 Estrellas(0)
    • 2 Estrellas(0)
    • 1 Estrellas(0)
Ordenar por:
Comentarios Recomendados
  • Comentarios Recomendados
  • Muy útil
  • Más Reciente
  • 2020-08-31 06:58:48

    товар пришел быстро (2 недели до спб). Продавцом остался доволен. Пружины очень жесткие это плюс. от колес толку не много. больше брал как дэкор

  • garma10
    2020-10-23 01:56:45

    la calidad se nota mucho y tiene un acabado increíble

  • 2020-08-05 19:22:29


  • yingkun
    2020-07-22 09:37:07

    Excellent and a must have upgrade.

  • Ben
    2020-09-01 00:20:22

    So, the springs are excellent as they hold the bed very steady on my Ender 3 V2. Unfortunately, the handles were not as useful as when installed, they tend to slip. I screwed on the screws on these handles and when I turn the handle, it sometimes just spins, rather than raise the bed. The original handle never slips, they raise the bed. I was a bit disappointed as they look better than the original handles but I decided to use these springs with the original handles.

    Comentarios (1)
  • 2020-09-04 10:46:48

    Les ressorts de ce pack sont très bons et fonctionnent parfaitement sur l'imprimante ENDER 3 Pro. Pour l'instant, j'utilise les écrous noirs de nivellement originaux. Les 4 écrous ont l'air de très bonne qualité...mais je ne peux pas en dire plus. J'ai acheté ce jeu pour les ressorts, je suis donc globalement satisfait.

  • 2020-08-12 04:27:54

    The springs in this pack are excellent. The Levelling nuts are largely fine, however the thread of one levelling nut was too large and couldn't tighten down, it just slipped instead. I am using 3 of the red nuts, and one of the original black nuts at the back. Largely I bought this set for the springs, so I am generally satisfied.

  • 2020-10-20 05:28:57

    Easier to set the height of the bed thanks to a slightly larger wheel. The springs are stiffer and seem perfect size of the ender 3. The look fancier than the plasic ones too!

  • Stouf
    2020-08-11 05:02:17

    Springs are really good but the wheels are bad to handle and get hot with the bed. The original ones from the Ender 3 Pro are way better. You can just find the springs without the wheels.

  • 2020-10-22 05:40:27

    Good quality, nice kit - will put it on my ender 3 pro in a few days! Very good springs, nice and strong wheels!


    Go to page


    Puedes estar interesado

    recommendation for you
    • US$16.99
    • US$3.99
    • US$10.72
    • US$1.49
    • US$12.99
    • US$6.99
    • US$39.99
    • US$3.27
    • US$14.66
    • US$2.19
    • US$206.00
    • US$259.00
    • US$24.99
    • US$7.80
    • US$399.00
    • US$21.48
    • US$12.50
    • US$5.78