Comentarios de Clientes

4.94 fuera de 5
Escribe un Comentario
  • Todos los comentarios (3385)
  • Imagen (709)
  • Video (14)
  • Todas Las Estrellas
    • Todas Las Estrellas(3385)
    • 5 Estrellas(3226)
    • 4 Estrellas(127)
    • 3 Estrellas(14)
    • 2 Estrellas(8)
    • 1 Estrellas(10)
Ordenar por:
Comentarios Recomendados
  • Comentarios Recomendados
  • Muy útil
  • Más Reciente
  • June-20 2020 04:58:48

    (UK customer) This is my first printer (I have had previous experience with industry grade printers but not consumer machines) I cannot speak highly enough of this printer. came within 48 hours and very well packaged (there were dents on the box but nothing major). Took me about 45-50 mins to assemble and check (recommend online videos for construction as the instructions get the job done but are very chaotic and no very clear). Used the filament included which was more than enough for the test

    Comentarios (5)
  • October-29 2020 02:55:15

    I giving you full stars review even if was not perfect for that price I can live with it. The problem I noticed immediately was on Y axis rail the wheels are bent so they bite to the rail cause annoying vibration so I took down othe wheel swap them around and order new for few quid from Amazon. nothing serious but it was small problem then the screws the head twists easily it seems B grade screws not really accurate but I am not worry about it I will replace them. otherwise I have no struglle with

  • July-09 2020 15:55:13

    Good Tool for this money, need use some time for setup, also can be easy to use with Ender Sliser. Бля это реально гавно, натрахался с настройкой кривого рабочего стола, Поставил две шайбы которых не было на креплении горячего подноса, выставил эксцентрики по своему, Пока подобрал режим для печати пластиком от ПК НИТ

  • June-10 2020 15:31:57

    Very good, but: Table rollers were too tight and they were deformed after a long time warehouse. Fortunately less pressure solved this problem. Small tilt of extruder, just unscrew a few screws, set correct position and it's ready. Working since first run. Of course table is not flat, because it is ender 3 hahah I am happy :)

  • June-03 2020 02:54:55

    Покупая этот принтер я уже почитал обзоры и ожидал что больших проблем с ним не будет, но был очень сильно удивлен, что собрав его по инструкции ничего не регулируя и настраивая прямо сразу получил очень хорошую печать. Прямо скажу, я не верил что это возможно, но принтер который

  • May-08 2020 02:20:27

    Привезли за 3 дня. Хорошо работает сразу после сборки. Пришлось пару раз молотком выпрямлять детальки, но это не страшно. Стоковая плата и стоковые кулера ощутимо шумят. Если брать не домой - то можно и не менять ничего. Для дома мне пришлось заменить кулера на noctua и плату на silentboard

  • March-01 2020 22:24:24

    Top demais esse seguro Alfândegario, recebi todo o valor da taxa de importação. Recomendo a todos do Brasil. Se inscrevam no Canal FJR DRONE STUDIO Tudo sobre Drones FIMI XIAOMI Canal YouTube Página Facebook Grupo do Facebook Me sigam no Instagram =•=•=•=•=•=•=•=•=•=•=•=•=•=•=•=•=•= #fpv #fjrdronestudio #midrone #taranis #frsky #fpvracer #droneracer

  • January-14 2020 01:27:33

    The Ender 3 is an amazing 3D printer and i highly recommend it for everyone who wants one. it printed perfectly when it came out of the box and was only a hour to assemble. there are hundreds of videos and guides out there on the internet that will solve any problem that can come when you use this printer and the replacement parts are very cheap. I would highly recommend this printer.

  • June-05 2020 18:36:24

    Superb after sale Customer Service! I didn't understand how my new 3D printer works, so I thought there was a breakdown. I asked for help and the request took a few days to process. Anyhow Banggood customer service helped me understand my new tool and they were so kind and polite. The printer itself has always worked. Banggood can be considered as one of the best online shopping site i ever used. Thanks to the superb after sales service!

  • March-26 2020 16:18:31

    for a beginner this is extremely budget friendly and I had trouble at first doing my initial first 3d prints but the help of the internet I manage to get everything situated owned it for about a month. mainly filament I use is PLA 1.75. i did manage to buy additional essential upgrades such as the tempered glass bed(its a must it sticks better) both LED bar light, and metal upgrades, you can also buy other essential are some pictures so you can know what you can build here. the tallest


    Go to page


    Puedes estar interesado

    recommendation for you
    • US$279.00
    • US$179.99
    • US$219.00
    • US$369.99
    • US$229.99
    • US$319.00
    • US$299.99
    • US$379.99
    • US$279.99
    • US$279.99
    • US$199.99
    • US$88.00
    • US$379.00
    • US$596.00
    • US$479.00
    • US$279.99
    • US$579.00
    • US$119.99