Comentarios de Clientes

4.5 fuera de 5
Ver todos 8 comentarios
Escribe un Comentario
  • Todos los comentarios (8)
  • Imagen (0)
  • Video (0)
  • Todas Las Estrellas
    • Todas Las Estrellas(8)
    • 5 Estrellas(5)
    • 4 Estrellas(2)
    • 3 Estrellas(1)
    • 2 Estrellas(0)
    • 1 Estrellas(0)
Ordenar por:
Comentarios Recomendados
  • Comentarios Recomendados
  • Muy útil
  • Más Reciente
Reseñas solo de tu país (Honduras)
|
Mostrar original

Una parte de la reseña se ha traducido automáticamente.

  • 13/04/2021

    Todavía estoy esperando una respuesta sobre qué hacer con el espectáculo porque la placa base está defectuosa.

    Comentarios
    Mostrar original
  • 18/05/2021

    very nice

    Comentarios
    Mostrar original
  • 19/10/2020

    Gracias por mi pedido.

    Comentarios
    Mostrar original
  • 14/01/2019

    Not for the faint hearted. Yes, it requires soldering of SMD components. This item is more work than the smaller flat rotaters because you need to solder 4 24 pin SMD chips.It is definitely easier than the spheric rotator in which you must also solder the little LED's at the side of a PCB. It is not clear from the description that this model runs on 12V. But it is mentioned on the PCB and in the schematic. Testing can be done on 5V, because it will rotate, and the LED's will light up. But the turning is off. I have yet to find out how to set the clock. One person mentioned that the 1.5K resistors are missing. Yes, but a set of 2.2K resistors are provided instead. Use these. There are NO spare LED's, so be careful not to loose even one. I ordered the blue kit, which has a red LED on the most outwards position. But that LED is not supplied. I took one from my box with spares. Be careful with the LED receiver. Follow the manual as you have not to follow the direction on the PCB. This is mentioned on several places. For the DC female connector you must disobey the manual as it is wrong at that point. Ignore the middle connector. I blew the U4 chip, with the result that LED 5 will not light up. I might repair that later on. Otherwise: a decent kit, but certainly a bit expensive. Oh, and I have not been busy with the reprogramming. All is in Chinese. I have to subtract points for that one. Their appear to be only 3 pre-loaded pictures. Value for price: too expensive, costs 2 points. Quality: for the exchanged resistors, missing outer LED, lack of description on how to set the clock, costs 2 points Appearance: lack of english description on how to replace the code: costs 1 point.

    Comentarios (5)
    Mostrar original
  • 19/02/2019

    good, fun project. :)

    Comentarios
    Mostrar original
  • 18/08/2020

    Muy bien empacado y sin daños llegó a mí. Te recomendaré. Gracias.

    Comentarios
    Mostrar original
  • 02/11/2019

    nice

    Comentarios
    Mostrar original
  • 26/02/2019

    i tried and failed (probably because of my fault). i will recomend this only for experienced electricians. you gona be soldering components smaller than 1mm.

    Comentarios
    Mostrar original
Show:

    Total 0 paginas

    Ir a la pagina

    Puedes estar interesado

    recommendation for you
    • US$36.99
    • US$16.79
    • US$26.99
    • US$14.99
    • US$15.99
    • US$7.99
    • US$10.99
    • US$32.99
    • US$12.99
    • US$15.99
    • US$8.99
    • US$4.59
    • US$10.99
    • US$17.99
    • US$6.99
    • US$14.99
    • US$24.99
    • US$30.99