Comentarios de Clientes

4.82 fuera de 5
Ver todos 447 comentarios
Escribe un Comentario
  • Todos los comentarios (447)
  • Imagen (37)
  • Video (3)
  • Todas Las Estrellas
    • Todas Las Estrellas(447)
    • 5 Estrellas(403)
    • 4 Estrellas(22)
    • 3 Estrellas(11)
    • 2 Estrellas(6)
    • 1 Estrellas(5)
Ordenar por:
Comentarios Recomendados
  • Comentarios Recomendados
  • Muy útil
  • Más Reciente
Reseñas solo de tu país (Honduras)
|
Mostrar original

Una parte de la reseña se ha traducido automáticamente.

  • 27/12/2020

    Llegué bien. Bonito proyecto de construcción. Una plantilla para LED es una necesidad para un ensamblaje de cubo exitoso. Tenga cuidado que es común cubo cátodo conectado a C1 - C8. Buena calidad. Reccomendar.

    Comentarios
    Mostrar original
  • 08/05/2021

    buena calidad, buen precio No se puede compilar sin un tamplate.

    Comentarios
    Mostrar original
  • 20/10/2020

    Gracias. Gracias. El producto ha llegado en buen estado. El uso sigue...

    Comentarios
    Mostrar original
  • 27/05/2021

    Un canon de buena calidad

    Comentarios
    Mostrar original
  • 20/12/2020

    ¡Buen artículo! Los LED son transparentes y difíciles de ver el efecto de la luz...

    Comentarios
    Mostrar original
  • 25/11/2016

    This is a great kit to improve your soldering skills. i have worked about 8 hours split over three days soldering the led grids, and this was great fun. Sadly my kit did not function. After a couple hours of troubleshooting, i noticed that the resistors R4 - R12 were 510 ohms in stead of the 220 ohms in the wiring diagram. I think they made a misstake during packing. colors are green, brown, brown. They should have been red, red, brown. of course. Since i am colorblind, i can imagine the misstake :) After replacing the correct resistors, the MCU still doesnt work. By manually pulling the resistors to ground, al the leds per segment light up. I think my STC12C5A60S2 has no code or is broken. Too bad.

    Comentarios (1)
    Mostrar original
  • 08/12/2017

    В самый раз для тех кто любит много пайки! Вот только мне забыли положить кабель питания ( не приятно) но не великая проблема есть блоки на 5 v. Шаблон делал сам не чего сложного размечал 15×15 мм. Шаблон у меня на ножках так мне показалось удобней ножки по 30мм. Всем удачной сборки!

    Comentarios
    Mostrar original
  • 27/09/2018

    this kit has everything necessary to build an 8x8x8 led cube. the printed circuit board is manufactured very well as per the Geekcreit standard. I will build it as soon as I have some free time. satisfied. questo kit ha tutto il necessario per costruire un cubo led 8x8x8. il circuito stampato è prodotto molto bene secondo lo standard Geekcreit. Lo costruirò non appena avrò del tempo libero. soddisfatto

    Comentarios (1)
    Mostrar original
  • 27/06/2017

    Please Read : If you downloaded the Instruction from Banggood or Hackaday It will tell you in Step 6 To connect the Cathode side to the Header pins of the controller board . THIS IS INCORRECT INFORMATION and it will make your cube malfunction it will act as if the programs bad you will get wild uncontrolled flashes of light and a very slow running cube which will make you believe there is a malfunction it your product... I have tried to build 4 of these so far and I have 4 malfunctioning cubes. I have commplained to Banggod customer service and finally got a correct answer out of them PLACE THE POSITIVE SIDE OF LEG ( ANODE ) Into the Header pins And then connect the Wires as described in the Instruction to the Negative layers All 8 Test it for your self Place a single LED positive leg in each of the first row header pins and the negative leg to where the wires goes and watch the program run Then reverse it and see the bad running program ... They seriously need to change these Instructions.... But out side of that One glitch It a pretty cool cube Also If you want to change the color of the LEd's Blue is OK but I like the Yellow and Purple or Orange LED's better I have post the Instructions as it is Now And A Screen shot of which leg of a LED is Pos. And Neg.. Good Luck on a great build

    Comentarios (3)
    Mostrar original
  • 16/09/2017

    Paid at 23.08.2017, received 12.09.2017, Shipping Method:Air Parcel Register. All conformity of description. Good quality. I'm completely satisfied. Lot of thank's for saller.

    Comentarios
    Mostrar original
Show:

    Total 0 paginas

    Ir a la pagina

    Puedes estar interesado

    recommendation for you
    • US$4.69
    • US$20.99
    • US$20.99
    • US$30.99
    • US$32.99
    • US$16.99
    • US$16.99
    • US$36.99
    • US$131.08
    • US$14.99
    • US$12.99
    • US$5.49
    • US$7.49
    • US$24.99
    • US$5.99
    • US$7.99
    • US$9.99
    • US$60.99