Comentarios de Clientes

4.82 fuera de 5
Ver todos 1711 comentarios
Escribe un Comentario
  • Todos los comentarios (1711)
  • Imagen (221)
  • Video (8)
  • Todas Las Estrellas
    • Todas Las Estrellas(1711)
    • 5 Estrellas(1550)
    • 4 Estrellas(83)
    • 3 Estrellas(33)
    • 2 Estrellas(22)
    • 1 Estrellas(23)
Ordenar por:
Comentarios Recomendados
  • Comentarios Recomendados
  • Muy útil
  • Más Reciente
Reseñas solo de tu país (Spain)
|
Mostrar original

Una parte de la reseña se ha traducido automáticamente.

  • 04/11/2015

    After some searching, I thought this information might be useful. I asked Banggod if I could stop the display from switching between time-temperature-date-day, and they replied no, that is not possible. Well, good news: IT IS POSSIBLE. I first soldered P3.6 and P3.7 to GND, which indeed did not change anything. I left them soledered (si I did not remove), and I soldered P1.4 to GND. This already made the display switch only between time and temperature (so no more date and day). I then soldered P1.3 as well, and TADAA, no more switching.

    Comentarios (1)
    Mostrar original
  • 11/11/2015

    При установке минут часы продолжают идти и секунды не устанавливаются в «ноль». В остальном часы очень даже хороши. В темноте автоматически снижают яркость до минимума, показывают температуру, которую можно поднастроить. Режим работы часов по умолчанию такой: 45 секунд показывают время, 5 сек - температуру, 5 сек - месяц/число и 5 сек - день недели (цифрой). Режим отображения часов легко менять, соединяя выводы 6 и 7 микроконтроллера с землей (по отдельности или вместе). Чтобы часы не были сверхъяркими, при сборке рекомендую заменить комплектные 8 резисторов 330 ом (510 ом) на резисторы 3.3 килоома, тогда яркость будет приемлемой и комфортной для восприятия. Точность часов очень даже хороша, -1 сек/сутки. При наличии свободного времени и желания, можно настроить еще точнее. Если соединить P1.4 и GND, часы будут показывать 55 секунд время и 5 секунд температуру. Если соединить P1.3 и GND, часы показывают 50 секунд время, 5 секунд месяц/число, 5 секунд день недели. Если подключить и P1.4 и P1.3 к GND, часы будут показывать только время.

    Comentarios
    Mostrar original
  • 01/12/2016

    This is all through-hole so is great for beginners or just for some soldering practice. The instructions, although somewhat poorly translated, were adequate. BE CAREFUL! The firmware on supplied MCU is programmed to enable the DS1302 RCT's trickle charge function but the kit is supplied with a non-rechargeable CR1220 lithium battery. This could result in undesirable results from the battery..... You should modify the circuit to put a diode in series with the battery or use a super capacitor rated for 5V instead.

    Comentarios (1)
    Mostrar original
  • 17/07/2015

    Паяльник в руках не держал уже больше 10 лет... И тут в просторах интернета набрел на это чудо. Решил заказать... Доставка до СПб заняла чуть меньше месяца. Посылка очень хорошо упакована, все компоненты на месте, даже есть небольшой запас по резисторам и крепежным винтикам)) Качество платы очень хорошее! Паять одно удовольствие, правда нужно приноровиться, так как компоновка очень плотная. Часы рабочие и очень симпатично смотрятся, стильно)) Покупкой остался доволен. Планирую еще приобрести данный товар, от друзей пошли заказы)) Рекомендую!

    Comentarios
    Mostrar original
  • 13/12/2016

    Hi, the clock works like the picture. 2nd digit. Where can I be wrong. My guess is the STC15W404 is faulty. Where can I find the new one? Thank you

    Comentarios (1)
    Mostrar original
  • 25/04/2015

    I have both red and blue kits. Assembly was fast and easy without any missing or faulty components. Both were working correctly but temperature was reading about 3 degrees high. I soldered a 120K resistor in parallel with R16 to bring the value down a bit. (top 10K near thermistor) It's now reading temperature correctly. 100k would work too, it depends on how high your reading. The LDR is very sensitive, if display is not dimming due to stray light I would point it down a bit or shield it slightly with a small length of heat shrink or drinking straw. Both of mine were working correctly pointing straight back.

    Comentarios (1)
    Mostrar original
  • 18/07/2021

    Este fue un gran proyecto. Mi primer reloj. Desafortunadamente las instrucciones estaban en chino, así que tuve que luchar para buscar instrucciones en inglés pero aún mejor encontré un video de YouTube de un reloj muy similar a este. Así que con la guía de YouTube y obteniendo algunas pistas de las reseñas de la gente pude armarlo con éxito. Si puedo hacerlo con poco conocimiento de electrónica cualquiera puede.

    Comentarios (1)
    Mostrar original
  • 26/06/2021

    Bom kit, fácil de montar, muito divertido e útil. Para quem tiver pouco conhecimento é só assistir o vídeo. Convém ter uma ponta de ferro de solda fina. Good kit, easy to assemble, very fun and useful. For those with little knowledge, just watch the video. It is a good idea to have a fine soldering iron tip.

    Comentarios
    Mostrar original
  • 05/10/2015

    This is really a very nice clock. I build the one with red displays, it is perfect to use in the bedroom. The dimming function works fine, in the dark the displays are dimmed to a minimum, but still good visible. Some remarks: The manual mentions to display the week (expecting something in the range 1..52) but in real it is a weekday (1..7). The manual mentions P3.6 and P3.7 grounding options to set the display mode, but these options do not work. The display always show the time for 45 seconds, then the temperature, the date and the weekday. Take care when mounting the 7-segment displays: sometimes they are floating above the pcb due to the soldering you did on the reverse side. Best method is to solder 1 pin in the upper row and 1 pin in the lower row. Repeat for all 4 displays (do not forget to mount display #3 upside down), then adjust if needed and solder the other pins. And finally... when you power up the clock for the first time, do not forget to perform a master reset (press both keys for 5 seconds) otherwise the clock may show very strange behaviour.

    Comentarios
    Mostrar original
  • 09/05/2015

    I wrote the detailed review Написал подробный обзор http://mysku.ru/blog/china-stores/31903.html В обзоре все подробно расписал с фотками

    Comentarios
    Mostrar original
Show:

    Total 0 paginas

    Ir a la pagina

    Puedes estar interesado

    recommendation for you
    • US$32.99
    • US$32.99
    • US$8.73
    • US$13.59
    • US$3.99
    • US$22.99
    • US$15.99
    • US$8.99
    • US$50.59
    • US$7.46
    • US$7.99
    • US$12.99
    • US$10.99
    • US$11.99
    • US$66.95
    • US$47.87
    • US$34.99
    • US$25.29