Una parte de la reseña se ha traducido automáticamente.
This is nice supply. It is really useful for DIY T12 soldering station ( https://goo.gl/P4pkWP ) because it fits perfectly in case for it: https://goo.gl/h118fq
Good product, works fine, I have removed resistor R19 2,32kE and repaced it with potentiometer 1kE and resistor 2kE in series so the output voltage is adjustable between 19,5V and 27,5V becouse I need 21V output.
The design of the power supply is good. It matches the specifications and there are no major corners cut. However there are some quality control problems. 1. R18 almost touches - and shorts to - the heat sink of the output diode - see photos 1 and 2 2. The flux residue on the back side of the board is not cleaned well - see photo 3 4. Some of the pins are very poorly trimmed - see photo 3 I did not even turn on the power supply before re-soldering R18 a bit to the side. Aside of the above it is a good value for the price.
Блок питания сделан качественно, качество сборки, пайки на высоте. Работает безупречно. На выходе выдаёт 23,8V, что очень неплохо. Под нагрузкой в диапазоне от 0 до 5А держит напряжение 23,8V (стабилизация очень хорошая). При превышении тока выше 5,1А срабатывает защита по току, что тоже очень хорошо. Минусы (очень незначительные): 1. Не точность в описании 6А (надо было писать 5А (120W)). 2. Выходной диод желательно поставить на 150 вольт. (40CTQ150). Есть очень подробное описание, с испытанием, схемой и доработками, данного блока на сайте: http://ru-sku.livejournal.com/1071408.html. Блоком и ценой (в данном магазине) очень доволен!!! Доставка в Россию примерно 24 дня. Рекомендую!
PS está trabajando fuera de la caja, el voltaje de salida es de 24.4V en inactividad. La tapa de entrada es nominal 82mF, el valor real es 72mF, lo cambié con 120mF. Las tapas de salida se clasifican 2x1000mF, el valor real es 1900mF, dejándolos como están. El tapón PWM es de sólo 22mF, cambiado con 47mF. Y gorra es bueno, no hay necesidad de cambiarlo. Después de los mods el voltaje de salida es de 24.45V en inactividad. Para la prueba de carga utilicé una gran resistencia cerámica, ajustada a 5,2Ω. Durante la prueba la tensión de salida fue de 24.52V en la carga. Después de 15 minutos el transformador fue calentado a 64.6C, diodo de salida a 44C, IC a 51.5C. Por lo tanto, después de que los mods PS está funcionando bien a 4.7A de corriente de salida, que es 115W de potencia.
Hola, he comprado y no me decepcionó con un descuento:). No hay ajuste de voltaje, pero dentro del rango normal de 23,8 voltios. No pude medir con precisión la corriente, pero mantiene aproximadamente la carga especificada, fui capaz de cargarla con una corriente de 5,65 A. La protección contra sobrecarga funciona! Recomiendo comprar con descuento:)
This is nice supply, especially for the price. It is really useful for DIY t12 soldering station (https://goo.gl/P4pkWP) because it fits perfectly in case for it: https://goo.gl/h118fq
Professionally packaged, non-defective delivery!
Отличный блок питания для самоделок. Почти не греется на нагрузке до 4 А. Стабильно выдает 24В.
Hands Up🙌 Muy buenas fuentes y muy compactas. Llevo comprando unas 8 de este modelo y nunca me han fallado 🍒 🔫 Son muy recomendables para espacios reducidos, eso si, hay que dejar agujeros de ventilación, yo no uso ventilador así queda un equipo silencioso👍