Comentarios de Clientes

4.96 fuera de 5
Ver todos 362 comentarios
Escribe un Comentario
  • Todos los comentarios (362)
  • Imagen (41)
  • Video (1)
  • Todas Las Estrellas
    • Todas Las Estrellas(362)
    • 5 Estrellas(353)
    • 4 Estrellas(6)
    • 3 Estrellas(2)
    • 2 Estrellas(0)
    • 1 Estrellas(1)
Ordenar por:
Comentarios Recomendados
  • Comentarios Recomendados
  • Muy útil
  • Más Reciente
Reseñas solo de tu país (Spain)
|
Mostrar original

Una parte de la reseña se ha traducido automáticamente.

  • 03/04/2014

    I used this with a Microchip PIC development board to interface to a 20x4 LCD display. With only 4 wires (including 2 for power) it's simple to set up and uses far fewer ports than the standard LCD parallel interface. As delivered the address pads A0 A1 and A2 are open but pulled high - so the I2C address is 0x4E. Ports P7,P6,P5,P4 of the PCF8574 interface to DB7,DB6,DB5,DB4 of the LCD Display. Port P3 is hard-wired to the backlight via a transistor: 1 = on / 0 = off. It's great that the backlight can be switched on and off via software with no additional hardware required. Port P2 is the display bit clock : E = 1 -> E = 0 active. Port P1 is R/W hardware Read/Write bit hardware : Read = 1 / Write = 0, so reading from the LCD display is possible, if required. Port P0 is RS Register Select : CmdReg = 0 / DataReg = 1. Display driver is HD44780 compliant. A great buy! I won't be interfacing to an LCD in future without it.

    Comentarios
    Mostrar original
  • 16/05/2015

    I bought some of these and found out that there are different models which need different pin configurations. Here is a beginners guide for the ones from Bangood: http://safe-power.appspot.com/i2c-en.html You need to download one library, and you are ready to enjoy LCDs on your arduino with only 2 Arduino pins occupied (plus GND and VCC). This little board saves you time and pins :-)

    Comentarios
    Mostrar original
  • 18/01/2019

    Good quality.

    Comentarios
    Mostrar original
  • 14/02/2021

    Llegada con éxito a Marruecos y con buena calidad de envasado

    Comentarios
    Mostrar original
  • 09/04/2021

    nice product. its really helpful to reduce the pins needed on a lcd. cool to see that there is a jumper include to enable or disable the onboard led. can be helpful in low power situations. the product was not damaged in shipping and the quality looks great!

    Comentarios
    Mostrar original
  • 11/09/2020

    Recibido bien en buen orden y bien embalado. Aún necesitamos probarlos.

    Comentarios
    Mostrar original
  • 27/02/2017

    The I2C interface module works fine on my blue 1602 LCD module. The I2C address is 0x27 out of the box so remember to modify your code accordingly. There is a very clear description that can be found here: http://arduino-info.wikispaces.com/LCD-Blue-I2C. It clearly describes the different available versions of the I2C interface. The one I received was version 3. When I first connected it and run the sample code I adjusted for the 16x2 display it did not seem to show any information on the display. The root cause was the potentiometer on the I2C interface not to be setup correctly out of the box. I needed to adjust it to change the contrast and show the characters on the screen. So I am happy with this interface as it reduces the connection to only 4 wires (2 for the power supply and 2 for the communication).

    Comentarios
    Mostrar original
  • 20/08/2013

    After receiving item, I test it with good results. Runs fine.

    Comentarios
    Mostrar original
  • 08/07/2020

    Fin trabajado en el primer intento. Preste atención a ajustar adecuadamente el contraste en el trimmer: los escritos en exhibición pueden parecer tan tenues que le hagan pensar que no funciona. Busqué la dirección con un escáner I2C (código fácilmente localizable en el sitio Arduino) y resultó para mi artículo 0x27. Para cambiar de dirección es necesario soldar puentes en los puntos A0-A1-A2 cerca del trimmer. Trabajó en el primer tiro. Tenga cuidado de ajustar el contraste con el trimmer, porque las letras en la pantalla pueden ser tan escamosas que no parece funcionar. Detectado la dirección con un escáner I2C (se puede encontrar fácilmente en el sitio web de Arduino) en mi muestra fue 0x27. Para cambiar de dirección es necesario soldar puentes en las canchas A0-A1-A2 cerca del trimmer.

    Comentarios
    Mostrar original
  • 19/10/2018

    nice package

    Comentarios
    Mostrar original
Show:

    Total 0 paginas

    Ir a la pagina

    Puedes estar interesado

    recommendation for you
    • US$13.85
    • US$11.36
    • US$16.50
    • US$8.39
    • US$10.20
    • US$34.49
    • US$6.99
    • US$15.37
    • US$5.24
    • US$3.99
    • US$3.67
    • US$2.47
    • US$8.04
    • US$6.89
    • US$3.44
    • US$9.23
    • US$827.99
    • US$264.99