Comentarios de Clientes

4.76 fuera de 5
Ver todos 112 comentarios
Escribe un Comentario
  • Todos los comentarios (112)
  • Imagen (18)
  • Video (0)
  • Todas Las Estrellas
    • Todas Las Estrellas(112)
    • 5 Estrellas(97)
    • 4 Estrellas(10)
    • 3 Estrellas(1)
    • 2 Estrellas(1)
    • 1 Estrellas(3)
Ordenar por:
Comentarios Recomendados
  • Comentarios Recomendados
  • Muy útil
  • Más Reciente
Reseñas solo de tu país (Spain)
|
Mostrar original

Una parte de la reseña se ha traducido automáticamente.

  • 08/05/2018

    This printer is very good value for the money. It prints well out of the box, has a good user interface and responsive touch screen, and a solid frame. The filament stop sensor works fine. I have used it several times to change filament when a spool runs out. I have not had a chance to test the power loss function. I have printed almost non stop with the printer since it arrived on 13.04.2018. Some reviews point out that it has an old Marlin firmware which does not home the Z-axis slowly on the second tap. This one is improved. It first homes Z quickly and then homes slower for the final measurement. There's one bug in the firmware. Sometime when I want to change filament it either doesn't pull the filament out or doesn't pull it in. This has happened a couple of times. Nothing happens and the extruder just sits there without spinning, but the progress bar moves as if it's running the motor. It works the next time I try. Mine arrived with slight shipping damage. The adjustment screw in one corner of the bed had broken loose so I had to glue it to the bed, but it has held up fine. IT does not affect the leveling, and the printer prints straight in all angles. The X-belt was a little loose, which caused the printer to skip a couple of times before I fixed it by installing a belt spring. Also, the X-pulley has slight wobble, which I think is the reason why the belt was adjuster so loose. It would be binding if it was tighter without a spring to take up the slack. The hot end cooling fan starter howling when I turned the printer on a couple of days ago so the bearings are probably shot. It should last much longer than a few weeks of printing. Minor problems for me. I bought the printer to make a big EDF jet model. I attached some photos of the prototype jet being printed.

    Comentarios
    Mostrar original
  • 02/01/2018

    I am very happy with the product. Delivery was quick. I have only one complaint: The software included on the flash-drive is faulty and could not be installed. It gave me error codes when I tried to install it. I found a place on the internet where I could download the software and the problem is now solved. The software is working fine. This is a great product and value for money! Johan

    Comentarios (5)
    Mostrar original
  • 04/08/2021

    El paquete fue recibido el día exacto como estaba programado, desde el almacén de la ZC y con la etiqueta de entrega de 1 semana. Todavía no lo he ensamblado, simplemente des-empaquetarlo y comprobar que todo parece estar bien con el contenido del paquete. Esperando poder publicar pronto una nueva reseña con las primeras impresiones en 3D.

    Comentarios (2)
    Mostrar original
  • 11/03/2018

    Colis arrivé en 12 jours à la Réunion. Attention taxe de douane à prévoir 45 €, colis livré par DHL ( Shipping Service). État visuel du colis à l'arrivée carton d'emballage assez abimé mais le contenu intact. Tout le nesséssaire est fournis dans le colis pour le montage le nivellement. Le montage de l'imprimant est rapide 10 minutes, le réglage du nivellement est un peu plus écorces. Le logiciel ( J.Creat ) fourni sur la clé USB est inutilisable fichier corrompu. J'ai pour ma part utilisé à simplify 3 D, et avec l'aide de vidéo Youtube https://www.youtube.com/watch?v=Kod43XFmo3g. pour les paramétrages, et le résultat est celui des photos que vous voyez imprimé en 0.2 mm. Résultat très bon avec le filament PLA fournis. Très satisfait de cette imprimante. Je précise que c'est ma première imprimante 3 D, et ma première expérience en impression 3 D. Bonne impression à tous.

    Comentarios
    Mostrar original
  • 27/08/2019

    I bought with direct mail and bangood refound all custom fee thanks. Rh z rod not in position when open box. yazıcı yi gümrük garantisi ile aldım gümrüğe geldikten sonra PTT den gümrük işlemlerinin tamamlanmasi için ödeme bilgileri istendi.ben gümrük ücretlerini bangood dan talep edeceğim için gümrüğe kendim gittim. bangood a sadece ödeme dekontlarini gönderdim fakat gümrük memurunun doldurduğu ödeme dekontunun kopyasını almamistim ve bangood o evragida istedi ve ikna etmek hayli güç oldu. tavsiyem gümrük vergisini ödemeden tüm evrakların kopyasını mutlaka alın. bangood ödediğim 453 TL lik gümrük vergisini geri ödedi.

    Comentarios (1)
    Mostrar original
  • LeoVIP1
    IT
    28/12/2017

    Ottimo prodotto, affidabile robusto e molto semplice da montare,il piatto da 30 cm consente stampe di grosse dimensioni, consiglio a tutti gli appassionati questa stampante , arriva pre assemblata , ideale per chi ha poco tempo a disposizione o sta iniziando ad entrare nel mondo delle stampanti 3D.SODDISFATTO oltre le aspettative per la qualita di stampa rispetto alle altre stampanti che usano frame in materiale plastico con consegueti perdite di qualità sul prodotto finito! Comodo il display touchscreen a colori e sopratutto se va via la corrente riparte dal punto di dove era rimasta senza perdere il lavoro iniziato!Incluso nel pacco c e una bobina di PLA, e una pen drive da 16GB.

    Comentarios (1)
    Mostrar original
  • 19/12/2018

    A impressora é de boa qualidade, mas veio com algumas partes amassadas, muito provavelmente na sua montagem, pois a embalagem estava intacta.

    Comentarios
    Mostrar original
  • 06/05/2019

    Everything was fine, the product is right. what I expected

    Comentarios
    Mostrar original
  • aomVIP2
    TH
    14/07/2019

    Package package for this product is very good, but the delivery of DSL is carried out with the most delay as much as possible. The operation of Learner L is not responsive to the customer, not the master according to the customer

    Comentarios
    Mostrar original
  • 25/06/2019

    Good end easy installed i didnt yet testing. After the testing i wişş write my view.

    Comentarios (1)
    Mostrar original
Show:

    Total 0 paginas

    Ir a la pagina

    recommendation for you
    • US$359.00
    • US$279.00
    • US$299.00
    • US$239.00
    • US$499.00
    • US$979.00
    • US$449.00
    • US$279.00
    • US$249.00
    • US$649.00
    • US$449.00
    • US$539.00
    • US$1,199.00
    • US$462.00
    • US$169.00
    • US$329.00
    • US$194.00
    • US$319.00