Comentarios de Clientes

4.71 fuera de 5
Escribe un Comentario
  • Todos los comentarios (285)
  • Imagen (27)
  • Video (0)
  • Todas Las Estrellas
    • Todas Las Estrellas(285)
    • 5 Estrellas(232)
    • 4 Estrellas(33)
    • 3 Estrellas(14)
    • 2 Estrellas(3)
    • 1 Estrellas(3)
Ordenar por:
Comentarios Recomendados
  • Comentarios Recomendados
  • Muy útil
  • Más Reciente
Reseñas solo de tu país (Honduras)
Mostrar original

Una parte de la reseña se ha traducido automáticamente.

  • 29/07/2021

    Parece que encaja bien y funciona como se anuncia.

    Mostrar original
  • 13/12/2016

    Arrived not warped and in excellent condition. After further analysis, it looks like the holes on top and the thru holes on the enclosure are perfect for 2-56 thread, use some 2-56 bolts and your golden ! Wish the cover didnt have such sharp edges (in the modeling, it'd be nice if the cover looked more like the D-M-NINE module. ) Still fits snugly though !

    Mostrar original
  • 21/11/2018

    è di buona fattura e si incastra molto bene, completo di due gusci fronte e retro e una serie di viti insomma colpeto ho aggiungi una centralina multiprotocollo e installato nella taranis x7

    Mostrar original
  • 25/12/2016

    Had to file the inside corners a little bit in order to easily fit the 4-in-1 module, as I didn't want to force the module into it. Fits into the Turnigy 9X module bay without any issue, and the antenna can be swiveled left-, right- and upwards with reasonable degree of room.

    Mostrar original
  • 08/04/2017

    A bit of a tight fit installing the actual module, but if you put one end in first, it drops right in. This doesn't come with screws but you can use the screws out of most eye glass repair kits to fasten it together

    Mostrar original
  • 03/03/2017

    Excelente acabamento, muito resistente, encaixe bom no rádio, cabe corretamente a pcb do multiprotocolo, pelo valor deveria vir a antena mas igual recomendo, útil.

    Mostrar original
  • 17/11/2016

    This fits my Taranis Plus perfectly! The only gripe is about the screws as mentioned before. I had some screws for the props on a Syma x11 and they fit "ok" in all 7 screw holes. Not perfect but good enough. I wish that screws were included or even if they were sold separately that would work. Overall super happy! It's a bit of a tight fit with 4 in 1 multiprotocol, but it fit in! Super happy!

    Mostrar original
  • 21/10/2016

    Fits fine only downside is its missing screws in the set. Maybe change the cover to a snapping version so you don't need to search for screws.

    Mostrar original
  • 23/07/2017

    This is a 3D printed part not moulded plastic and so the finish and appearance is not great. It does the job though. This is intended for the Frsky but can be used on Turnigy 9XR Pro with some tweaks. I use this STM32 4-in01 module: You need to remove all the screw posts inside the case so that the module board can be flushed as low as possible otherwise the it will not mate securely with the header pins inside the Turnigy transmitter bay. It is because the pins are shorter than those of a Frsky transmitter. The clips on both sides of the case do not lock securely into the Turnigy bay because of dimensional discrepancies. You need to fit a ~1mm spacer inside the trasnmitter bay to lift the whole module up. The clips will then lock nice and tight.

    Mostrar original
  • 30/01/2017

    I use this case for my taranis and it fits perfect. The only thing is that as described it came with no screws. That was a bit tricky to find srews that fits.

    Mostrar original

    Total 0 paginas

    Ir a la pagina

    Puedes estar interesado

    recommendation for you
    • US$112.99
    • US$199.99
    • US$15.99
    • US$28.99
    • US$21.99
    • US$17.99
    • US$49.99
    • US$21.99
    • US$39.99
    • US$20.99
    • US$8.99
    • US$131.99
    • US$14.99
    • US$110.99
    • US$67.99
    • US$85.99
    • US$66.99
    • US$329.99