I installed this transmitter module in my Devo 10 with Deviationtx v5. Pro: small, seems to work well (not thoroughly tested yet), reasonable price, clear instructions for installation. Nice to transform this Walkera transmitter into a multi functional (for different brands) one! Con: the supplied antenna is too short for use in the Devo10. I had to use another antenna (Product ID: 1005363). There is no room within the Devo to mount it in the upper part, without overheating the excisting transmitter module (crf) The supplied wires are too short too. Unfortunatly the spacing on this module of the soldering pins is too small to use breadboard cables (lke Product ID: 974006). If it would have been the same spacing like the NRF24L01 module (Product ID: 89812) it would save a lot of time and give a more neat and reliable connection. Now I had to bend over the pins in order to prevent a shortcut between the pins.

I installed this transmitter module in my Devo 10 with Deviationtx v5. Pro: small, seems to work well (not thoroughly tested yet), reasonable price, clear instructions for installation. Nice to transform this Walkera transmitter into a multi functional (for different brands) one! Con: the supplied antenna is too short for use in the Devo10. I had to use another antenna (Product ID: 1005363). There is no room within the Devo to mount it in the upper part, without overheating the excisting transmitter module (crf) The supplied wires are too short too. Unfortunatly the spacing on this module of the soldering pins is too small to use breadboard cables (lke Product ID: 974006). If it would have been the same spacing like the NRF24L01 module (Product ID: 89812) it would save a lot of time and give a more neat and reliable connection. Now I had to bend over the pins in order to prevent a shortcut between the pins.

I installed this transmitter module in my Devo 10 with Deviationtx v5. Pro: small, seems to work well (not thoroughly tested yet), reasonable price, clear instructions for installation. Nice to transform this Walkera transmitter into a multi functional (for different brands) one! Con: the supplied antenna is too short for use in the Devo10. I had to use another antenna (Product ID: 1005363). There is no room within the Devo to mount it in the upper part, without overheating the excisting transmitter module (crf) The supplied wires are too short too. Unfortunatly the spacing on this module of the soldering pins is too small to use breadboard cables (lke Product ID: 974006). If it would have been the same spacing like the NRF24L01 module (Product ID: 89812) it would save a lot of time and give a more neat and reliable connection. Now I had to bend over the pins in order to prevent a shortcut between the pins.

This product is well made. it came with necessary wires and a heat shrink. I will install it in my Devo 10 by the end of the week and will put up the videos on my channel. This is my unboxing video: https://youtu.be/dsgDE3iyA90

This product is well made. it came with necessary wires and a heat shrink. I will install it in my Devo 10 by the end of the week and will put up the videos on my channel. This is my unboxing video: https://youtu.be/dsgDE3iyA90

This product is well made. it came with necessary wires and a heat shrink. I will install it in my Devo 10 by the end of the week and will put up the videos on my channel. This is my unboxing video: https://youtu.be/dsgDE3iyA90

Впаял в devo10 согласно схеме, проверил на v911, v977, k110 - работает нормально. Паял прямо на выведенные штырьки, колодку не выпаивал. залудил, припаял, залил термоклеем, потом уже в сам пульт впаивал к предварительно выведенным проводам где у меня раньше другие два модуля жили. и ещё один доп. провод вывел от B7. После чего обновил прошивку на 5.0 чтобы k110 работал и проверил - всё пока что хорошо. Антенну вывел как попало, см. фото. также пригодилась цветная термоусадка тоже с бангуда и немного применил синей изоленты ввиду её магических свойств.

Впаял в devo10 согласно схеме, проверил на v911, v977, k110 - работает нормально. Паял прямо на выведенные штырьки, колодку не выпаивал. залудил, припаял, залил термоклеем, потом уже в сам пульт впаивал к предварительно выведенным проводам где у меня раньше другие два модуля жили. и ещё один доп. провод вывел от B7. После чего обновил прошивку на 5.0 чтобы k110 работал и проверил - всё пока что хорошо. Антенну вывел как попало, см. фото. также пригодилась цветная термоусадка тоже с бангуда и немного применил синей изоленты ввиду её магических свойств.

Впаял в devo10 согласно схеме, проверил на v911, v977, k110 - работает нормально. Паял прямо на выведенные штырьки, колодку не выпаивал. залудил, припаял, залил термоклеем, потом уже в сам пульт впаивал к предварительно выведенным проводам где у меня раньше другие два модуля жили. и ещё один доп. провод вывел от B7. После чего обновил прошивку на 5.0 чтобы k110 работал и проверил - всё пока что хорошо. Антенну вывел как попало, см. фото. также пригодилась цветная термоусадка тоже с бангуда и немного применил синей изоленты ввиду её магических свойств.

I installed this on my Devo 7E, work perfectly...

I installed this on my Devo 7E, work perfectly...

I installed this on my Devo 7E, work perfectly...

The circuit board of Devo 8s is different from Devo10. If you want to connect CS_2401 with circuit board, there is an other soldering point. In Deviation firmware , the hardware ini has to be changed. Take attention to the semicolon. Devo8s bindet with V911, V977 and Walkera V120. Telemetrie (Batterievoltage, Batterytemperature ) runs with V120/RX2636. I made no rangetest.

The circuit board of Devo 8s is different from Devo10. If you want to connect CS_2401 with circuit board, there is an other soldering point. In Deviation firmware , the hardware ini has to be changed. Take attention to the semicolon. Devo8s bindet with V911, V977 and Walkera V120. Telemetrie (Batterievoltage, Batterytemperature ) runs with V120/RX2636. I made no rangetest.

The circuit board of Devo 8s is different from Devo10. If you want to connect CS_2401 with circuit board, there is an other soldering point. In Deviation firmware , the hardware ini has to be changed. Take attention to the semicolon. Devo8s bindet with V911, V977 and Walkera V120. Telemetrie (Batterievoltage, Batterytemperature ) runs with V120/RX2636. I made no rangetest.

Модуль отличный, работает как надо.

Модуль отличный, работает как надо.

Модуль отличный, работает как надо.

It is a great value ! If you need to add a protocol to your Devo I strongly recommend to take this one as you will have directly 3 protocols in 1. It is easy to solder the wires for CC2500 and A7105 but be careful you need to be advised that the NRF24L01 need solder less than 0.5 mm wire on 1 very small pin next to others (see picture enclosed)... You need to have good iron, some flux and a good magnifying. The best would have been to work with a heat air gun + some solder paste and kapton tape to seal the other pin's... See my install video here : https://www.youtube.com/watch?v=mVSXBsbSqGA

It is a great value ! If you need to add a protocol to your Devo I strongly recommend to take this one as you will have directly 3 protocols in 1. It is easy to solder the wires for CC2500 and A7105 but be careful you need to be advised that the NRF24L01 need solder less than 0.5 mm wire on 1 very small pin next to others (see picture enclosed)... You need to have good iron, some flux and a good magnifying. The best would have been to work with a heat air gun + some solder paste and kapton tape to seal the other pin's... See my install video here : https://www.youtube.com/watch?v=mVSXBsbSqGA

It is a great value ! If you need to add a protocol to your Devo I strongly recommend to take this one as you will have directly 3 protocols in 1. It is easy to solder the wires for CC2500 and A7105 but be careful you need to be advised that the NRF24L01 need solder less than 0.5 mm wire on 1 very small pin next to others (see picture enclosed)... You need to have good iron, some flux and a good magnifying. The best would have been to work with a heat air gun + some solder paste and kapton tape to seal the other pin's... See my install video here : https://www.youtube.com/watch?v=mVSXBsbSqGA

A very good mod/upgrade for DEVO TX indeed. For DEVO7E pin13 soldering is a pain in the back side, but otherwise is quite easy. Works great, as intended, also boost it's signal with high gain external antennae.

A very good mod/upgrade for DEVO TX indeed. For DEVO7E pin13 soldering is a pain in the back side, but otherwise is quite easy. Works great, as intended, also boost it's signal with high gain external antennae.

A very good mod/upgrade for DEVO TX indeed. For DEVO7E pin13 soldering is a pain in the back side, but otherwise is quite easy. Works great, as intended, also boost it's signal with high gain external antennae.

Don't get me wrong; soldering this thing in is a substantial PITA, but it's definitely do-able (even with my shaky hands). Now that it's done I can bind my Devo10 to so many different things! I just wish they sold a Devo10 with this module pre-installed.

Don't get me wrong; soldering this thing in is a substantial PITA, but it's definitely do-able (even with my shaky hands). Now that it's done I can bind my Devo10 to so many different things! I just wish they sold a Devo10 with this module pre-installed.

Don't get me wrong; soldering this thing in is a substantial PITA, but it's definitely do-able (even with my shaky hands). Now that it's done I can bind my Devo10 to so many different things! I just wish they sold a Devo10 with this module pre-installed.

https://www.youtube.com/watch?v=pwpZbcUsbcg When you modify the DEVO transmitter until now, the selection of the module was the trouble. Increasing the module and the remodeling of labor increases. Time is also required. And whether fit into how the transmitter module and antenna, was troubled while looking at the piece of the puzzle. I was no longer bothering to be happy. It's thanks to this module. Really remodeling in 30 minutes to complete. It has become much easier. I want to recommend to everyone.

https://www.youtube.com/watch?v=pwpZbcUsbcg When you modify the DEVO transmitter until now, the selection of the module was the trouble. Increasing the module and the remodeling of labor increases. Time is also required. And whether fit into how the transmitter module and antenna, was troubled while looking at the piece of the puzzle. I was no longer bothering to be happy. It's thanks to this module. Really remodeling in 30 minutes to complete. It has become much easier. I want to recommend to everyone.

https://www.youtube.com/watch?v=pwpZbcUsbcg When you modify the DEVO transmitter until now, the selection of the module was the trouble. Increasing the module and the remodeling of labor increases. Time is also required. And whether fit into how the transmitter module and antenna, was troubled while looking at the piece of the puzzle. I was no longer bothering to be happy. It's thanks to this module. Really remodeling in 30 minutes to complete. It has become much easier. I want to recommend to everyone.