Comentarios de Clientes

4.77 fuera de 5
Escribe un Comentario
  • Todos los comentarios (62)
  • Imagen (3)
  • Video (0)
  • Todas Las Estrellas
    • Todas Las Estrellas(62)
    • 5 Estrellas(55)
    • 4 Estrellas(2)
    • 3 Estrellas(3)
    • 2 Estrellas(2)
    • 1 Estrellas(0)
Ordenar por:
Comentarios Recomendados
  • Comentarios Recomendados
  • Muy útil
  • Más Reciente
Reseñas solo de tu país (Honduras)
  • July-05 2017 03:29:38

    Both board and display are quite nice. What I really like is that this board have replaceable chip, so you can use ti to program ATmega 328 chips:

  • July-12 2017 11:53:33

    It works. Thank u

  • June-19 2017 10:01:47

    The two pieces off 2.8" UNO Module arrived broken Do you replace me the products???

  • December-10 2020 12:39:11

    Reasonably well packet. Both units also in anti static plastic. Package was delivered in about 10 days at my door in the Netherlands, so not bad at all.

  • November-01 2015 18:03:57

    After 4 weeks i finally had my hands on this product. But it was not easy to let it work. So found the good driver!! When you know the driver you can easily let it work. For me i found it after 2 days. So this have i done. At the back on my module stand with black marker 68090 it seem to stand for the diver RM68090 but under that name you can not found it. So after hard google. i found on another site that the RM68090 is similar on the ILI9325 so when you get the unkown driver error try this one.

    Comentarios (2)
  • October-05 2016 09:07:27

    плата контроллера "завелась" сразу (читай рекомендации продавца), дисплей - через пару часов "плясок с бубном"; продавец пишет, что драйвер ili9341, однако завелось и стало показывать тестовые картинки с примером для ili9325?! Буду разбираться дальше-одно радует - оно работает!

  • September-16 2015 18:09:23

    One row of pins was bent very, very slightly on the Uno - but nothing that would affect the function in any way. The display is indeed only held in place by a small piece of adhesive and foam on the shield. If you plan to choose another orientation anyway that's a plus. Otherwise it's a good idea to fixate it. I had the touch display up and running in about an hour's time. The provided "driver" is a good starting point for the proper pin configuration. In the end a slightly modified version of the

    Comentarios (1)
  • November-14 2016 08:49:52

    Ein kleiner Stift wird mitgeliefert. Die Oberfläche des Touchpads ist etwas "schwammig". Leider sind durch das Aufstecken des TFT-Moduls die Port-Pins des Arduino nicht mehr direkt erreichbar was die Möglichkeiten etwas einschränkt. Als separates Anzeige-/Eingabe-Modul für komplexe Daten ideal.

  • September-17 2015 16:51:09

    The tft driver - ILI9341 but not standard library. The working library, I found Zarówno Arduino Uno, (melduje się na COM 9) jak i LCD z nakładką dotykową, pracują dobrze. Jedynie podczas wysyłania danych, na czarnym tle w dole ekranu, pojawiaja się białe linie, do wysokości około 1/3 wyświetlacza. Wyświetlacz ma driver ILI9341, niestety, nie chce pracować ze standardowymi bibliotekami, działające "MCUFried" znalazłem na forum: http

  • September-14 2015 17:45:22

    First off, the screen is not well attached to the board, so it can get rip off the board easily! The UNO came with the connector pins bend (probably due to bad packaging for transport). Screen is white, now to figure a way to program it (it doesn't seem that the normal TFT library work on it). I tried to get it to fit with the acrylic case, it is ok but the SD slot is being annoying.


    Total 0 pages

    Go to page


    Puedes estar interesado

    recommendation for you
    • US$13.99
    • US$8.99
    • US$17.99
    • US$15.99
    • US$17.51
    • US$2.99
    • US$3.36
    • US$6.99
    • US$23.99
    • US$4.49
    • US$2.99
    • US$3.99
    • US$5.99
    • US$2.33
    • US$2.69
    • US$2.99
    • US$6.49
    • US$94.99