Comentarios de Clientes

4.97 fuera de 5
Escribe un Comentario
  • Todos los comentarios (36)
  • Imagen (2)
  • Video (0)
  • Todas Las Estrellas
    • Todas Las Estrellas(36)
    • 5 Estrellas(35)
    • 4 Estrellas(1)
    • 3 Estrellas(0)
    • 2 Estrellas(0)
    • 1 Estrellas(0)
Ordenar por:
Comentarios Recomendados
  • Comentarios Recomendados
  • Muy útil
  • Más Reciente
  • August-14 2018 18:23:10

    muito bom agora é fazer meu projeto para ver como se sai.

    Comentarios
  • October-11 2018 13:41:27

    Nice board to have for different projects. The soldering on the Funduino board isn't the best, but nothing too critical.

    Comentarios
  • July-26 2020 09:22:42

    Look OK, not used yet

    Comentarios
  • September-06 2016 10:57:58

    These are fantastic, using both together (of course) to create a servo breakout board with full control. Careful though, the nano is sensitive, I blew one by not having enough current to run servos, think i short circuited it, prob best to push 5v 3A into the VIN pin instead of the through the barrel connector which i think is limited to a few hundred ma. Live and learn! ;)

    Comentarios
  • July-26 2016 14:19:29

    Con este escudo, se solucina el problema que tenemos a la hora de conectar sensores al arduino porque te da para cada pin de señal un pin v+ y otro de gnd para alimentar al sensor. Solo destacar que me llegaron con algunos pines doblados y rotos, pero nada que con 5 minutos de soldador no se solucione... ;)

    Comentarios
  • May-19 2016 08:24:50

    I make a lot of gizmo's using Arduino's. Often I use veroboard and add the extra 12->5V power supply and connectors. This takes time and money. This board has it all done for you! The power supply is brought out to each pin so you can add sensors very easily. For the money it's cheaper to buy 5 of these than the 5 Nano's and prototyping boards. The micro-usb serial programming interface works perfectly too.

    Comentarios
  • March-29 2016 23:59:57

    Nano V3 works as a Nano V3 should. I like this model with the loose pins as it is more versatile than if the pins are pre-soldered. The expansion board makes prototyping with the Nano much easier by allowing easy connection of battery power and I/O to the Nano.

    Comentarios
  • February-09 2016 19:11:28

    in one package. As you can see from the Banggood pgotos the Nano needs the headers soldering in; an easy job if you use the Funduino as a jig by inserting the pins in the sockets then placing the Nano on the stubs before soldering.

    Comentarios
  • January-19 2017 05:07:45

    Va a serme muy util para los distintos montajes que realizo para el robot que estoy montando.

    Comentarios
  • November-25 2019 13:07:24

    item as description

    Comentarios
Show:

    Go to page

    Go

    Puedes estar interesado

    recommendation for you
    • US$6.07
    • US$4.99
    • US$5.88
    • US$7.99
    • US$4.83
    • US$5.99
    • US$13.67
    • US$5.99
    • US$6.32
    • US$13.41
    • US$4.81
    • US$8.95
    • US$6.99
    • US$11.23
    • US$9.99
    • US$6.78
    • US$3.99
    • US$72.99