Comentarios de Clientes

4.65 fuera de 5
Ver todos 187 comentarios
Escribe un Comentario
  • Todos los comentarios (187)
  • Imagen (26)
  • Video (3)
  • Todas Las Estrellas
    • Todas Las Estrellas(187)
    • 5 Estrellas(158)
    • 4 Estrellas(11)
    • 3 Estrellas(7)
    • 2 Estrellas(4)
    • 1 Estrellas(7)
Ordenar por:
Comentarios Recomendados
  • Comentarios Recomendados
  • Muy útil
  • Más Reciente
Reseñas solo de tu país (Spain)
|
Mostrar original

Una parte de la reseña se ha traducido automáticamente.

  • 11/06/2017

    The board looks very promising. I just did a quick test and noticed that the mounting holes are connected to the positive lead once again. Please be aware of this

    Comentarios (3)
    Mostrar original
  • 22/06/2017

    All that is done it's good, i just wanted to replace one 5v regulator to one dataflash chip for blackbox, all the rest is fine and good. My stress test: https://www.youtube.com/watch?v=HjC2DeYDPto

    Comentarios
    Mostrar original
  • 19/06/2017

    I've been having tons of trouble with my builds but this one did good. I broke it before putting it on by switching the lead to a pigtail, but was able to bond it with E6000 and it's holding so far. Dumb mistake -- don't be like me, start with a pigtail connection. It's a great board that I was able to make fly immediately and it feeds plenty of power into the brother hobby 1407 on 4s. Such a beast...

    Comentarios
    Mostrar original
  • 21/06/2017

    I have build 2 quads with the Star4 and wanted to try out the new Star3. Easy build, the RX pads are VERY tiny and behind the usb, i didnt see them at first. This one is slightly cheaper and makes for a very light build. I am going to do a full video review soon. Been running the StarF4 on my 5" for weeks with no issues. And the 3" pictured is my first used of the F3.

    Comentarios (6)
    Mostrar original
  • 20/09/2017

    this little board is actually great for an all in one would love to see a 40a or even a 60a board in the future gives me a clean feed and osd works great

    Comentarios (1)
    Mostrar original
  • 09/10/2017

    super clean build works well whit bf 3.2 and t1 tornado 1407 motors i use 8k/4K dynamic filter and dshot600 and are super smooth!

    Comentarios (1)
    Mostrar original
  • 08/08/2017

    This F3 with OSD! Current and Bec's is great! Hooked it up with some HiKV motors 2306 2650Kv, and it performs great! But do remember, RED means PLUS on mounting holes not MINUS! USB is located in better place than on F4 version! It has buzzer and led and RX port. Also 5v out. Can't wait for 20x20 AIO version!!! At least with 18Amps!

    Comentarios
    Mostrar original
  • 27/10/2017

    Its my second Board. the first one just went to smoke after lipo plug. Banggood send my a replacemant with no hassle! very good custumer service there! My Second Board had about 20 Lipos, then a ceramic capacitor from the esc just gone away.(bad factory soldering) I think its just a bit poor Quality, but this Board rocks for sure. I have a fatass 600g Chamelion with 2307 2522kv Hyperlites on gemfan 5152. And this board can Take that with ease, 140+ Amp on Punchouts. I will never go back this solution is the future. Just need better Quality Controll. I would Pay 20 bugs more for sure.

    Comentarios
    Mostrar original
  • 05/10/2018

    Funcionando a la perfección, noto que se calientan los variadores pero por ahora funciona bien

    Comentarios
    Mostrar original
  • 15/05/2018

    Everything worked. Solder ports for video and sbus are small just be careful and hit glue after to keep from touching.

    Comentarios
    Mostrar original
Show:

    Total 0 paginas

    Ir a la pagina

    Puedes estar interesado

    recommendation for you
    • US$92.99
    • US$44.99
    • US$21.99
    • US$26.44
    • US$18.89
    • US$27.59
    • US$17.59
    • US$23.39
    • US$17.24
    • US$28.39
    • US$11.50
    • US$18.39
    • US$6.89
    • US$10.99
    • US$16.09
    • US$6.86
    • US$13.99
    • US$6.89