Comentarios de Clientes

4.98 fuera de 5
Ver todos 394 comentarios
Escribe un Comentario
  • Todos los comentarios (394)
  • Imagen (66)
  • Video (26)
  • Todas Las Estrellas
    • Todas Las Estrellas(394)
    • 5 Estrellas(388)
    • 4 Estrellas(5)
    • 3 Estrellas(1)
    • 2 Estrellas(0)
    • 1 Estrellas(0)
Ordenar por:
Comentarios Recomendados
  • Comentarios Recomendados
  • Muy útil
  • Más Reciente
Reseñas solo de tu país (Spain)
|
Mostrar original

Una parte de la reseña se ha traducido automáticamente.

  • 19/12/2016

    This is some quality kit. The box itself it came in is very sturdy and the parts fit well in the box without any movement. (We've all had a box from china at some point flattened, crushing some crucial component amirite?) The foam is light yet tuff & sturdy. And it has all the canals for wiring already layed out. There are slots in the wings for a transmitter and receiver and the kit contains carbon covers to cover them up. The manual is in almost perfect English and is good to follow. A generous amount of stickers is also supplied to get the red stripes as shown on the example photo's. The kit contains a lot of quality carbon parts. The spars are really thick comparing to the plane itself. It looks like it could take a beating. Two main spars, each elevon has a spar and two more spars (L+R) along the leading edge of the plane. This plane constructionwise, is not for beginners. You'll need to cut away some molding residue and the supplied PCB needs a good soldering hand (It's a BEC to power the servo's) Although i'm raving about the good quality, it might look like one wing half is slightly warped. I'll have to look into that. Can't wait to try this one out :D

    Comentarios (1)
    Mostrar original
  • 08/10/2017

    Качество хорошее, материал плотный! Есть не большие недочеты на всех швах от пресс формы, но аккуратно ножом можно подрезать. модель не супер отлита. Пена вроде спечена плотно. На элевонах нужно ставить петли, но это моё мнение. Комплект весь, но не нет проставки для мотора, Spare Part Motor Mount Product ID: 1150379 - в комплекте её нет! Придется заказывать отдельно. На фотографиях на сайте она присутствует! Цена супер. Покупал во время годовщины интернет магазина. Quality is good, the stuff is tight! There are no big flaws in all seams from the mold, but you can trim it with a knife. the model is not super cast. The foam seems to be sintered densely. On Elevons you need to put a loop, but this is my opinion. The complete set, but there is no spacer for the motor, Spare Part Motor Mount Product ID: 1150379 - in the complete set it is not present! Have to order separately. She is present on the photos on the site! The price is super. Bought during the anniversary of the online store. RCPOiNT

    Comentarios
    Mostrar original
  • 06/07/2017

    small but valuable wing i rigged mine with an emax 2205s 2300kv and 30a esc and this thing loves to fly fast and well. if you put a led board on the back like the one in the picture (not mine) it is a perfect race wing. you can also carry it outside your backpack for a mountain ride, it will fly in every condition.

    Comentarios
    Mostrar original
  • 03/02/2017

    This little wing is very tough, has a nice finish and is beautiful. The precut holes for the servos, ESC, RX and TX made it very easy to build and give it a very nice finish look. Surprisingly the manual both for the flying wing and the on board PCB is perfect. Speaking of PCB, it is a very nice touch. The center part hole is large for a flying wing of this category, you can easily fit a 3S 2200mhA batterie. Further more the package is well done, no damage and quick delivery (I order two separately) Overall a very good flying wing, thanks!

    Comentarios (1)
    Mostrar original
  • 11/10/2017

    Pacco arrivato in buone condizioni nella confezione è presente anche un power distribution board con modulo BEC che credevo fosse incluso . Inserito un Flight controller CC3D motore sunnysky X2204 2300 Kv ricevitore frsky V8R7 II ESC EMAX 20A un po grosso bisogna ricavare spazio . Attenzione nel scegliere la posizione per il perno di plastica da forare nell'ala. Tenersi piu distante vedi foto ala sinistra dall'alto.

    Comentarios
    Mostrar original
  • 10/08/2020

    Esta ala es un tanque. tan duro y muy buen piloto para principiantes y pilotos avanzados. si usted es un principiante sólo tiene que empezar con 3s 1800mah o 4s 1300mah sólo para mantener el sobre todo el peso y no tiene ningún problema en el lanzamiento. para pilotos más avanzados puedes ir 6s 3000mah para súper largo timbre y tendrás que afinar los pids para que sea fácil el lanzamiento. Para bigginers es perfecto porque no importa cuántas veces para cobrarlo duro se lo tomará como un hombre de verdad. Gran ala. Esta es mi tercera ala S800. uno para mí uno para mi amigo como regalo y 3 a Ordené porque me encantó y todavía tengo mi viejo s800 conmigo.

    Comentarios (4)
    Mostrar original
  • 14/01/2017

    The concept of the wing is sooooo gooood, I hope it fly how it looks like :)

    Comentarios
    Mostrar original
  • 29/12/2018

    Easy to build and looks awesome. Perfect product and great finish. Not to mention that it is very resistant . My favorite build so far is with a BR2212 motor and 80 amp esc . I use 2200mah 3s and get 10 to 20 minutes flight time depending on how hard I drive it.

    Comentarios (2)
    Mostrar original
  • 18/05/2017

    EPP material with no adjustments, exactly as removed from the mold. Parts fit together pretty well. See attached image for my way of mounting the motor. On the right wing, the foam beads seems to have weaker bonds. Will see after a crash or two :) Easy to glue using "prenandez/Aderpren" (in Romania/Moldova) - the usual shoes glue. Nice non-magnetic screws, but 8 (4+4) strong magnets on the lid. In order to use a magnetic compass close to the center of the wing it will be necessary to remove the magnets and invent an other fixing mechanism for the lid. It fits a APC7x5 propeller if the motor is not too short. I used double adhesive to keep the wings on the main part.

    Comentarios
    Mostrar original
  • 31/03/2018

    Love this model. Here is a video of my 4th S800 build: https://youtu.be/FD4a30jmtz0 I recommend this model to beginners and skilled fpv operators. I modded mine a lot but the mods made it fly very good. Buy yours now!

    Comentarios
    Mostrar original
Show:

    Total 0 paginas

    Ir a la pagina

    Puedes estar interesado

    recommendation for you
    • US$6.99
    • US$67.89
    • US$15.52
    • US$18.29
    • US$80.99
    • US$72.99
    • US$56.99
    • US$8.99
    • US$18.99
    • US$16.59
    • US$124.99
    • US$109.00
    • US$73.99
    • US$120.00
    • US$89.99
    • US$83.99
    • US$69.99
    • US$29.99