Comentarios de Clientes

4.8 fuera de 5
Ver todos 30 comentarios
Escribe un Comentario
  • Todos los comentarios (30)
  • Imagen (1)
  • Video (0)
  • Todas Las Estrellas
    • Todas Las Estrellas(30)
    • 5 Estrellas(26)
    • 4 Estrellas(3)
    • 3 Estrellas(0)
    • 2 Estrellas(1)
    • 1 Estrellas(0)
Ordenar por:
Comentarios Recomendados
  • Comentarios Recomendados
  • Muy útil
  • Más Reciente
Reseñas solo de tu país (Spain)
|
Mostrar original

Una parte de la reseña se ha traducido automáticamente.

  • 29/07/2019

    makes a nice light effeckt on my ar mini wing (pnp motor) wiring to FC is straight forward and its fully supported by inav ;-)

    Comentarios
    Mostrar original
  • 16/08/2018

    16 LED ring with addressable RGBW LEDs The LEDs is easily driven by a microcontroller for example an Arduino. Only a single data line is required for control. I had a issue where half of the PCB is geting warm. the resistor used in serie with data input was on the wrong place. the resistor is connected over 5V and ground causing a current of 15mA even if the leds are off. The resistor can be remove or swapped with the capacitor. See image. The LEDs shines good and can be set to be very bright. if LEDs are driven at high brightness remember cooling.

    Comentarios (1)
    Mostrar original
  • 16/11/2017

    Really good product. Was a little bit confused because only 3/4th of the pixel were addressed and colors were others than programmed. Switching to RGBW instead of RGB solved the problem. Conclusion: Got a better product than advertised.

    Comentarios (1)
    Mostrar original
  • 17/08/2018

    This does what I expect it to do but it is a lot smaller than I was expecting. I was hoping to use it for an IronMan costume but it is not big enough.

    Comentarios
    Mostrar original
  • 22/05/2018

    Be Warned: This is not WS2812 or SK6812. After several hours of trying to find out why the last four pixels were dead and showing the wrong colors, I found that this LED also has white. The order of the pixels is GRBW. Banggood need to change the description of this item.

    Comentarios (1)
    Mostrar original
  • 09/03/2018

    The rings are pretty good, in programming with Arduino you must input a 21 LED number instead of 16. A couple of LED's need 2 PWM signals to go to another.

    Comentarios
    Mostrar original
  • 27/12/2017

    There is no way to solder the connections right because all 4 holes are covered by the leds!! I'd appreciate Banggod have them replaced by ones correctly assembled!

    Comentarios (1)
    Mostrar original
  • 18/01/2018

    Кольцо идеально подошло на крыло Z-84 вокруг двигателя

    Comentarios
    Mostrar original
  • 05/01/2021

    Te ves bien, se acerca la prueba.

    Comentarios
    Mostrar original
  • 24/11/2020

    Rink RGB de buena calidad y brillo. ¡Recomendado!

    Comentarios
    Mostrar original
Show:

    Total 0 paginas

    Ir a la pagina

    Puedes estar interesado

    recommendation for you
    • US$6.99
    • US$5.74
    • US$15.32
    • US$3.99
    • US$8.07
    • US$4.99
    • US$4.61
    • US$10.38
    • US$9.23
    • US$9.23
    • US$27.99
    • US$12.99
    • US$13.79
    • US$3.99
    • US$4.99
    • US$8.99
    • US$4.59
    • US$10.38