Comentarios de Clientes

4.67 fuera de 5
Escribe un Comentario
  • Todos los comentarios (15)
  • Imagen (0)
  • Video (0)
  • Todas Las Estrellas
    • Todas Las Estrellas(15)
    • 5 Estrellas(12)
    • 4 Estrellas(2)
    • 3 Estrellas(0)
    • 2 Estrellas(1)
    • 1 Estrellas(0)
Ordenar por:
Comentarios Recomendados
  • Comentarios Recomendados
  • Muy útil
  • Más Reciente
Reseñas solo de tu país (Honduras)
  • July-30 2020 18:19:54

    good

    Comentarios
  • June-27 2020 16:46:05

    looks good. not tryed yet

    Comentarios
  • VIP3
    US
    March-04 2019 13:53:35

    1. One of the 3D printed rear ear's broke off when I tried to install it. OK, checked the to see if there would be a clearances issue, if I super glued both of them on. No problem.... 2. Installed the front 3D parts, along with the front & back tracks. Releativly no problems. When I tried to test it, just made a bunch of noise. From the nylon axle hubs, just spinning inside the track hubs. I used Masking tape to wrap around the axle hubs. However, I have to remove it, to use the wheels.

    Comentarios
  • September-10 2018 00:23:36

    These wheels worked for my wpl truck. 3d printed parts are not the best quality. Some of the holes were too big for the screws because of print quality. Came with all the hardware needed to install even screws. Overall good product. Would like to have 3d print files to reprint items that were not so great.

    Comentarios
  • January-16 2019 22:49:19

    With the 3d printed axle /hub fittings supplied,you can easily switch from ordinary 4X4 to All terrain tracks-pop them into the load tray when running on wheels.Fairly sturdy units - I thought hey might throw the tracks when running but I have not had any problems there.A more powerfol motor would be good though as it is sometimes a bit of a struggle to move.At least double the fun factor!

    Comentarios
  • January-05 2019 03:54:27

    The idea is good, but there is one drawback. Plastic rubs against plastic and creates additional friction, which is very bad for drives (in my case wpl millitary track 1:16). Plastic drive can not stand, the motor is heated. Now, if we thought out and made a cat through plastic sleeves, or it would be better through bearings, it would be an ideal option.

    Comentarios (1)
  • October-23 2018 12:33:30

    Для замены обычных колес машинки WPL и повышения проходимости. Требует замены стокового мотора на более мощный

    Comentarios
  • September-07 2018 04:37:09

    para mi wpl b1 y c24

    Comentarios
  • May-13 2019 00:58:51

    passen leider nicht auf Q61.

    Comentarios
  • April-03 2019 03:46:38

    Good for WPl crawlers

    Comentarios
Show:

    Total 0 pages

    Go to page

    Go

    Puedes estar interesado

    recommendation for you
    • US$31.89
    • US$5.58
    • US$20.89
    • US$7.80
    • US$18.01
    • US$5.46
    • US$3.05
    • US$15.99
    • US$43.99
    • US$10.25
    • US$29.99
    • US$39.88
    • US$16.95
    • US$10.73
    • US$12.13
    • US$8.72
    • US$91.76
    • US$130.00