Brilliant Value For Money and very accurate Information and works directly with the DJI Naza Lite and Naza m v2 I was a little worried about setting this up but it is actually quite easy just following the pics on here. Only downside is there is no menu to remove certain items from display. However you can have 3 modes one which includes no display. The reason I purchased it was for the GPS status as a green led from the other side of a field is hard to see. All in all a good buy A+++++

Brilliant Value For Money and very accurate Information and works directly with the DJI Naza Lite and Naza m v2 I was a little worried about setting this up but it is actually quite easy just following the pics on here. Only downside is there is no menu to remove certain items from display. However you can have 3 modes one which includes no display. The reason I purchased it was for the GPS status as a green led from the other side of a field is hard to see. All in all a good buy A+++++

Brilliant Value For Money and very accurate Information and works directly with the DJI Naza Lite and Naza m v2 I was a little worried about setting this up but it is actually quite easy just following the pics on here. Only downside is there is no menu to remove certain items from display. However you can have 3 modes one which includes no display. The reason I purchased it was for the GPS status as a green led from the other side of a field is hard to see. All in all a good buy A+++++

The S-OSD is great ! full funktional, easy to install and the two switchable datascreens are fully customicable. the third screen is plain, no data. must be switched by one single PWM pulse of RC transmitter chanel. ad or remoove enything with config osd 2.0 https://arducam-osd.googlecode.com/files/Config_OSD_20.zip it can be used with NAZA M lite and M2 (ther red and the orange) adjusting the artificial horizon is done via NAZA softwer by configuring the gimball outputs. you can connect LIPO's up to 4S at the ENGV IN+ - an have an adjustable aleart displayed when the flightbattery is getting to low. the only thing i sudgest is to remoove the black connectorhousing from the GPS and LED pins then they will hold on much better. to connect the S-OSD to a PC you need SKU080201 FTDI adapter and some pins to solder on like SKU039144 the conection starting at the pushbutton is: Black(-),NC(no conect),red(+),green(DATA1),wite(DATA2),and NC GPS has to be unplugged for updating else it blocks the bootloader !!! Before chanching Parameters always press RESET(pushbutton) enjoy

The S-OSD is great ! full funktional, easy to install and the two switchable datascreens are fully customicable. the third screen is plain, no data. must be switched by one single PWM pulse of RC transmitter chanel. ad or remoove enything with config osd 2.0 https://arducam-osd.googlecode.com/files/Config_OSD_20.zip it can be used with NAZA M lite and M2 (ther red and the orange) adjusting the artificial horizon is done via NAZA softwer by configuring the gimball outputs. you can connect LIPO's up to 4S at the ENGV IN+ - an have an adjustable aleart displayed when the flightbattery is getting to low. the only thing i sudgest is to remoove the black connectorhousing from the GPS and LED pins then they will hold on much better. to connect the S-OSD to a PC you need SKU080201 FTDI adapter and some pins to solder on like SKU039144 the conection starting at the pushbutton is: Black(-),NC(no conect),red(+),green(DATA1),wite(DATA2),and NC GPS has to be unplugged for updating else it blocks the bootloader !!! Before chanching Parameters always press RESET(pushbutton) enjoy

The S-OSD is great ! full funktional, easy to install and the two switchable datascreens are fully customicable. the third screen is plain, no data. must be switched by one single PWM pulse of RC transmitter chanel. ad or remoove enything with config osd 2.0 https://arducam-osd.googlecode.com/files/Config_OSD_20.zip it can be used with NAZA M lite and M2 (ther red and the orange) adjusting the artificial horizon is done via NAZA softwer by configuring the gimball outputs. you can connect LIPO's up to 4S at the ENGV IN+ - an have an adjustable aleart displayed when the flightbattery is getting to low. the only thing i sudgest is to remoove the black connectorhousing from the GPS and LED pins then they will hold on much better. to connect the S-OSD to a PC you need SKU080201 FTDI adapter and some pins to solder on like SKU039144 the conection starting at the pushbutton is: Black(-),NC(no conect),red(+),green(DATA1),wite(DATA2),and NC GPS has to be unplugged for updating else it blocks the bootloader !!! Before chanching Parameters always press RESET(pushbutton) enjoy