Comentarios de Clientes

4.91 fuera de 5
Ver todos 77 comentarios
Escribe un Comentario
  • Todos los comentarios (77)
  • Imagen (10)
  • Video (0)
  • Todas Las Estrellas
    • Todas Las Estrellas(77)
    • 5 Estrellas(72)
    • 4 Estrellas(3)
    • 3 Estrellas(2)
    • 2 Estrellas(0)
    • 1 Estrellas(0)
Ordenar por:
Comentarios Recomendados
  • Comentarios Recomendados
  • Muy útil
  • Más Reciente
Reseñas solo de tu país (Spain)
|
Mostrar original

Una parte de la reseña se ha traducido automáticamente.

  • 15/01/2020

    Muy buena tabla, pero tiene algunas caídas. No puedes apagar el tablero y cargar la batería al mismo tiempo. También el hardware serie 2: GPIO 16 y 17 no funcionan mientras se utiliza el OLED, para resolver este problema he utilizado el cable puente para que el OLED rst se conecta a 3V, y cortar el rastro a GPIO 16. Aparte de eso es una muy buena tabla a un precio aún mayor!

    Comentarios (1)
    Mostrar original
  • 01/03/2018

    This board works great, I was able to get both the WiFi and the OLED up and running. The OLED is a bit tricky, it's not connected to the standard I2C pins, its SDA pin is 4 and SCL pin is 15. You can set this up by adding Wire.begin(4, 15) to your setup code. The display's I2C address is 0x3C. You will also need to use the OLED_RST pin to enable the display: pinMode(16,OUTPUT); digitalWrite(16, LOW); delay(50); digitalWrite(16, HIGH); After applying these settings I2CScan can find the display and most SSD1306 Arduino libraries work (for example the Adafruit SSD1306 works after changing Wire.begin() to Wire.begin(4, 15) and setting the reset pin and the I2C address).

    Comentarios (6)
    Mostrar original
  • 15/05/2019

    Works. I've read some overcomplicated about the display. I got it to work with U8g2lib. I used the following constructor line: U8G2_SSD1306_128X64_NONAME_F_HW_I2C u8g2(U8G2_R0, /* reset=*/ U8X8_PIN_NONE, /* clock=*/ 16, /* data=*/ 17); this has to be changed to the right pins so it becomes: U8G2_SSD1306_128X64_NONAME_F_HW_I2C u8g2(U8G2_R0, /* reset=*/ 16, /* clock=*/ 15, /* data=*/ 4); This got it working for me with the usual U8g2lib functions.

    Comentarios (2)
    Mostrar original
  • 09/03/2018

    Works great. here is how to get working with arduino IDE: https://github.com/espressif/arduino-esp32#installation-instructions Also, LCD might be a bit tricky install library: "ESP8266 and ESP32 Oled driver for SSD1306 display" Look at my attached pictures for minimum demo.

    Comentarios
    Mostrar original
  • 26/04/2019

    Очень быстро доставили(СDEK прямо к дверям квартиры).Очень шикарно упаковано(хоть с десятого этажа бросай).Проверил сразу---все работает.Огромное спасибо продавцу!!!!Все отрицательные отзывы для меня ---бред!Работают круче чем Аli.Наверное спасибо конкурентной борьбе....:):):)

    Comentarios
    Mostrar original
  • 16/02/2018

    Very nice little ESP32 board with OLED display, when it came i plugged it to usb and demo program was running but I am not able to get it working now, i tried to do it with information from comments but did not worked for me, also tried to check IC2 address with ic2 scanner but without success, but board works well.

    Comentarios
    Mostrar original
  • 29/12/2017

    It looks good at first glance The screw is very close to the antenna, I hope that is not a problem

    Comentarios
    Mostrar original
  • 23/04/2018

    Module works good so far. Next is to exercise the complete flash. Thanks to eagle for the message below how to get the OLED operating.

    Comentarios
    Mostrar original
  • 22/02/2019

    Happy with this module. Working as it should. Easy to programming with the tips on this site

    Comentarios
    Mostrar original
  • JayVIP4
    CA
    10/05/2018

    Very good price and quality

    Comentarios
    Mostrar original
Show:

    Total 0 paginas

    Ir a la pagina

    Puedes estar interesado

    recommendation for you
    • US$28.99
    • US$55.99
    • US$9.99
    • US$46.19
    • US$12.69
    • US$95.15
    • US$9.90
    • US$28.86
    • US$12.40
    • US$4.99
    • US$26.55
    • US$33.99
    • US$6.60
    • US$3.99
    • US$59.91
    • US$6.99
    • US$33.72
    • US$19.62