El extrusor es bueno, pero tuve problemas con el montaje ender 3 pro. el lado estaba en contacto con la varilla roscada y lo estaba atascando así que tuve que recortar un lado como se muestra en la imagen.

the extruder is good but i had problems with mounting it to ender 3 pro. the one side was in the contact with threaded rod and was jamming it so i had to trim one side as shown in the picture.

El extrusor es bueno, pero tuve problemas con el montaje ender 3 pro. el lado estaba en contacto con la varilla roscada y lo estaba atascando así que tuve que recortar un lado como se muestra en la imagen.

Incorporando problemas, avanzando. Buena suerte. A mis necesidades, la mejor extrusora 3D. En envases exigentes, llegó rápidamente. Producto de buena calidad. Mi mecánico dice que es la mejor extrusora 3D.

In demanding packaging, arrived quickly. Good quality product. According to my mechanic, the best 3D extruder. Igényes csomagolásban, gyorsan megérkezett. Jó minőségű termék. A szerelőm szerint, a legjobb 3D extruder.

Incorporando problemas, avanzando. Buena suerte. A mis necesidades, la mejor extrusora 3D. En envases exigentes, llegó rápidamente. Producto de buena calidad. Mi mecánico dice que es la mejor extrusora 3D.

excelente servicio

excelente servicio

excelente servicio

Llegó a tiempo y está bien.

Přišlo včas a v pořádku.

Llegó a tiempo y está bien.

Product arrived as described. Packaged very well. No damage to product. I purchased this item specifically to convert 1 side of my Mankati 3D printer to print with 1.75mm flex filament. Now I can print with 3mm and 1.75mm filament. The extruder mounts perfectly to a nema 17 stepper motor. This extruder can work with flexible filament. When I first used it I had to change the e-steps value. Because this item is transparent it helps to see any problems. When I tried my first print the flexible filament was escaping between the rollers. After some trial and error I found that the original spring is too strong/stiff. NOTE: IF YOU WANT TO PRINT WITH FLEX FILAMENT YOU WILL NEED TO CHANGE THE SPRING. I used 2 springs from a bicycle quick-release skewer. These springs have much less strength than original spring. See photos. These worked perfectly. After some tuning of print speed and flow the print quality is excellent. Using the existing spring I expect that this extruder will work very well. I will continue to use the extruder with the new springs. Banggood, I would recommend you supply a weaker spring; maybe half the strength would be ok.

Product arrived as described. Packaged very well. No damage to product. I purchased this item specifically to convert 1 side of my Mankati 3D printer to print with 1.75mm flex filament. Now I can print with 3mm and 1.75mm filament. The extruder mounts perfectly to a nema 17 stepper motor. This extruder can work with flexible filament. When I first used it I had to change the e-steps value. Because this item is transparent it helps to see any problems. When I tried my first print the flexible filament was escaping between the rollers. After some trial and error I found that the original spring is too strong/stiff. NOTE: IF YOU WANT TO PRINT WITH FLEX FILAMENT YOU WILL NEED TO CHANGE THE SPRING. I used 2 springs from a bicycle quick-release skewer. These springs have much less strength than original spring. See photos. These worked perfectly. After some tuning of print speed and flow the print quality is excellent. Using the existing spring I expect that this extruder will work very well. I will continue to use the extruder with the new springs. Banggood, I would recommend you supply a weaker spring; maybe half the strength would be ok.

Product arrived as described. Packaged very well. No damage to product. I purchased this item specifically to convert 1 side of my Mankati 3D printer to print with 1.75mm flex filament. Now I can print with 3mm and 1.75mm filament. The extruder mounts perfectly to a nema 17 stepper motor. This extruder can work with flexible filament. When I first used it I had to change the e-steps value. Because this item is transparent it helps to see any problems. When I tried my first print the flexible filament was escaping between the rollers. After some trial and error I found that the original spring is too strong/stiff. NOTE: IF YOU WANT TO PRINT WITH FLEX FILAMENT YOU WILL NEED TO CHANGE THE SPRING. I used 2 springs from a bicycle quick-release skewer. These springs have much less strength than original spring. See photos. These worked perfectly. After some tuning of print speed and flow the print quality is excellent. Using the existing spring I expect that this extruder will work very well. I will continue to use the extruder with the new springs. Banggood, I would recommend you supply a weaker spring; maybe half the strength would be ok.

Super reemplazo en mi tevo tarántula pro

super en remplacement sur ma tevo tarantula pro

Super reemplazo en mi tevo tarántula pro

Recibidos en buen estado aún no han sido probados.

Received in good order have yet to test.

Recibidos en buen estado aún no han sido probados.

Funcionando perfectamente.

Working perfectly.

Funcionando perfectamente.

funciona bien, pero ten en cuenta si quieres instalar en un Ender 3. No encaja en el Ender porque el tornillo de avance se interpone en el camino. Puedes usar una lima o una amoladora para limar una pieza del estuche de la extrusora para que encaje, pero es bastante trabajo. Al final, vale la pena el esfuerzo, le ayudará a lograr velocidades de impresión más rápidas sin subextrusión debido a que la impresora se salta los pasos. Era un poco más ruidoso que el extrusor de stock cuando se utilizaba avance lineal y velocidades de impresión rápidas, pero esto se puede resolver ajustando el "tornillo" que tensa los engranajes del extrusor

works well, but be warned if you want to install on an Ender 3. It doesn't fit the Ender because the lead screw gets in the way. You can use a file or grinder to file out a piece of the extruder's case so it fits, but it's quite some work. In the end it's worth the effort, it will help you achieve faster printing speeds with no underextrusion due to the printer skipping steps. It was a bit noisier than the stock extruder when using linear advance and fast printing speeds, but this can be sorted out by adjusting the "screw" that tensions the extruder gears

funciona bien, pero ten en cuenta si quieres instalar en un Ender 3. No encaja en el Ender porque el tornillo de avance se interpone en el camino. Puedes usar una lima o una amoladora para limar una pieza del estuche de la extrusora para que encaje, pero es bastante trabajo. Al final, vale la pena el esfuerzo, le ayudará a lograr velocidades de impresión más rápidas sin subextrusión debido a que la impresora se salta los pasos. Era un poco más ruidoso que el extrusor de stock cuando se utilizaba avance lineal y velocidades de impresión rápidas, pero esto se puede resolver ajustando el "tornillo" que tensa los engranajes del extrusor

Parece estar funcionando bien, no estoy seguro de cómo desmontarlo para fijarlo directamente en la parte superior del hotend con el montaje del surco, podría no ser posible sin romperlo. Aparte de eso, está bien.

Seems to be working okay, not sure how to take it apart in order to fix it directly on top of the hotend with groove mount, might not be possible without breaking it. Other than that, it's fine.

Parece estar funcionando bien, no estoy seguro de cómo desmontarlo para fijarlo directamente en la parte superior del hotend con el montaje del surco, podría no ser posible sin romperlo. Aparte de eso, está bien.