Comentarios de Clientes

4.81 fuera de 5
Escribe un Comentario
  • Todos los comentarios (48)
  • Imagen (5)
  • Video (0)
  • Todas Las Estrellas
    • Todas Las Estrellas(48)
    • 5 Estrellas(41)
    • 4 Estrellas(6)
    • 3 Estrellas(0)
    • 2 Estrellas(1)
    • 1 Estrellas(0)
Ordenar por:
Comentarios Recomendados
  • Comentarios Recomendados
  • Muy útil
  • Más Reciente
Reseñas solo de tu país (Honduras)
  • May-28 2020 20:15:11

    Bonjour, Pour commencer, l'article livré pourra avoir une apparence différente comme tel a été le cas pour le mien mais cela n'influe en rien sa qualité (Voir photo). L'accroche magnétique est excellente et ne diminue pas vraiment malgré une chauffe intensive du plateau (100°C pour l'ABS). Aucun soucis pour décoller un print quelques minutes après qu'il soit terminé. Restera à voir la durée de vie de la surface lors d'une utilisation relativement soutenue. L'installation prend quelques

    Comentarios
  • January-10 2020 04:06:25

    is small for cr10s pro

    Comentarios
  • May-04 2019 13:05:32

    Description says usable up to 80°, but in facts, only up to 70° like you could see on the pic. Can't be used for nylon or abs.

    Comentarios
  • March-29 2019 05:01:26

    für 20x20 super aber nicht für 30x30

    Comentarios
  • March-25 2019 14:37:52

    Why would you ship it in a bag with my pulleys and bearings?? There is a large dent in the middle of the surface from being squished into the pulleys. Then the edges have large dents, not to mention one side being folded over. I dont think I'll even use this now as my prints which always start in the center are not going to be flat. I am sure I would have given 5 stars had this been protected some what during shipping.

    Comentarios
  • January-02 2021 03:45:42

    Bought this for my cr10s and its not as good as the others I got, don't know if i got a bad one or not but prints just don't seem to want to come off in one piece. Thanx BG

    Comentarios (1)
  • February-13 2020 15:03:55

    smels like hot plastic at 80C. Also hard to remove petg from it at this temp. Works good for 60C, light smell, so far not bothering me. Meted a bit when I homed the printer and kept nozzle close to bed for about 2 min.

    Comentarios
  • January-08 2021 18:52:42

    Llego en buenas condiciones solo unos pequeños raspones y hundimientos en la placa pero nada que afecte la impresión.

    Comentarios
  • November-30 2020 08:53:00

    está bien pero el iman tiene muchas burbujas de aire y tienes que pincharlas para que te pueda imprimir bien

    Comentarios
  • StigN
    NO
    September-22 2020 14:49:12

    Great functionality, however it was a little shorter than expected. does not fill the bed of CR10 S Pro V2.

    Comentarios
Show:

    Total 0 pages

    Go to page

    Go

    Puedes estar interesado

    recommendation for you
    • US$21.00
    • US$15.99
    • US$399.00
    • US$4.99
    • US$30.99
    • US$10.99
    • US$4.67
    • US$3.99
    • US$2.99
    • US$5.66
    • US$259.00
    • US$206.00
    • US$299.00
    • US$2.39
    • US$23.99
    • US$209.00
    • US$42.99
    • US$24.99