I ordered this chassis as 1:1 replacement for the stock one of my A959. It looks good and solid so I try to rebuild my A959 on this chassis. This will not work out out of the box there is some rework needed or you need to buy more update parts. Here are some issue I had: The major issue is the the drilled holes for rod mount the suspension arms is about 1mm to low. The result is that the stock (plastic) suspension arms will no longer fit. It seems that the full metal updates fit this situation (I ordered them but still backordered so I can't fully prove) but you than will have a asymmetric mounted suspension... I don't like it. Second issue I found is that the chassis is about 1mm shorter than the stock one so your main shaft is to long. So you likely will have to shorten yours or you will hear stage noise from the differentials. Additionally the cover plate for the shaft will not fit perfectly. Third minor issue: The mount for the servo is to high this time you have 1mm space between the servo and the chassis. While steering the servo motor is moving up and down and make some clicking noise. Fourth minor issue: There is not enough space mount the controls unit (ESC and receiver). As I plan to upgrade the car to Brushless motor I didn't care about this fact. Anyway you will have to find a solution. Sixth issue this one should be mentioned as well: The pins for mounting the steering linkage are - again - a little bit sort. As the mounting sockets that comes with the cassis are not fixed it may happen that the pins lost track and steering is badly influenced. Either you need to fix the sockets on chassis or try to get longer pins. Some other things I found but not treat as an issue: The dust cover for the reduction gear and the motor do not fit. Even with cover you have always some dust and sand that will get into the gears so if you keep it open it's much faster and easier to to clean it. I had updated my one with steel gears so they will last a little bit longer. Summery: This is a really nice looking stable and massiv chassis that will add some extra weight to you car. The weight is good as you will have a more "grounded" car which will advance the handling. On the other hand do not expect that you can replace the chassis 1:1 there is a lot of rework that needs to be done. To solve most of the stuff I designed some extra parts for 3D printing e.g. to level the suspension mounting and the diffs. I may post them when finished.

I ordered this chassis as 1:1 replacement for the stock one of my A959. It looks good and solid so I try to rebuild my A959 on this chassis. This will not work out out of the box there is some rework needed or you need to buy more update parts. Here are some issue I had: The major issue is the the drilled holes for rod mount the suspension arms is about 1mm to low. The result is that the stock (plastic) suspension arms will no longer fit. It seems that the full metal updates fit this situation (I ordered them but still backordered so I can't fully prove) but you than will have a asymmetric mounted suspension... I don't like it. Second issue I found is that the chassis is about 1mm shorter than the stock one so your main shaft is to long. So you likely will have to shorten yours or you will hear stage noise from the differentials. Additionally the cover plate for the shaft will not fit perfectly. Third minor issue: The mount for the servo is to high this time you have 1mm space between the servo and the chassis. While steering the servo motor is moving up and down and make some clicking noise. Fourth minor issue: There is not enough space mount the controls unit (ESC and receiver). As I plan to upgrade the car to Brushless motor I didn't care about this fact. Anyway you will have to find a solution. Sixth issue this one should be mentioned as well: The pins for mounting the steering linkage are - again - a little bit sort. As the mounting sockets that comes with the cassis are not fixed it may happen that the pins lost track and steering is badly influenced. Either you need to fix the sockets on chassis or try to get longer pins. Some other things I found but not treat as an issue: The dust cover for the reduction gear and the motor do not fit. Even with cover you have always some dust and sand that will get into the gears so if you keep it open it's much faster and easier to to clean it. I had updated my one with steel gears so they will last a little bit longer. Summery: This is a really nice looking stable and massiv chassis that will add some extra weight to you car. The weight is good as you will have a more "grounded" car which will advance the handling. On the other hand do not expect that you can replace the chassis 1:1 there is a lot of rework that needs to be done. To solve most of the stuff I designed some extra parts for 3D printing e.g. to level the suspension mounting and the diffs. I may post them when finished.

I ordered this chassis as 1:1 replacement for the stock one of my A959. It looks good and solid so I try to rebuild my A959 on this chassis. This will not work out out of the box there is some rework needed or you need to buy more update parts. Here are some issue I had: The major issue is the the drilled holes for rod mount the suspension arms is about 1mm to low. The result is that the stock (plastic) suspension arms will no longer fit. It seems that the full metal updates fit this situation (I ordered them but still backordered so I can't fully prove) but you than will have a asymmetric mounted suspension... I don't like it. Second issue I found is that the chassis is about 1mm shorter than the stock one so your main shaft is to long. So you likely will have to shorten yours or you will hear stage noise from the differentials. Additionally the cover plate for the shaft will not fit perfectly. Third minor issue: The mount for the servo is to high this time you have 1mm space between the servo and the chassis. While steering the servo motor is moving up and down and make some clicking noise. Fourth minor issue: There is not enough space mount the controls unit (ESC and receiver). As I plan to upgrade the car to Brushless motor I didn't care about this fact. Anyway you will have to find a solution. Sixth issue this one should be mentioned as well: The pins for mounting the steering linkage are - again - a little bit sort. As the mounting sockets that comes with the cassis are not fixed it may happen that the pins lost track and steering is badly influenced. Either you need to fix the sockets on chassis or try to get longer pins. Some other things I found but not treat as an issue: The dust cover for the reduction gear and the motor do not fit. Even with cover you have always some dust and sand that will get into the gears so if you keep it open it's much faster and easier to to clean it. I had updated my one with steel gears so they will last a little bit longer. Summery: This is a really nice looking stable and massiv chassis that will add some extra weight to you car. The weight is good as you will have a more "grounded" car which will advance the handling. On the other hand do not expect that you can replace the chassis 1:1 there is a lot of rework that needs to be done. To solve most of the stuff I designed some extra parts for 3D printing e.g. to level the suspension mounting and the diffs. I may post them when finished.

URUAV frame, not JINGXI like pictures

URUAV frame, not JINGXI like pictures

URUAV frame, not JINGXI like pictures

Buen Chasis 👍😁 Llegó muy rápidamente, como se especifica en la descripción, un Chasis muy agradable, bien hecho y bien embalado, llegó sin ningún golpe o falta de piezas. Sígueme en mi canal de Tubo DRRC Stunt, y pronto habrá un video del montaje en el modelo 👉 https://www.youtube.com/channel/UCYPCHCvorQKBgTh_xUys0Og Gracias a todos Gran vendedor, lo recomiendo

Nice nice Chassis 👍😁 Arrived very quickly, as specified in the description, a really nice Chassis, well made and well packed, it arrived without any knocks or lack of parts. Follow me on my you tube channel DRRC Stunt, and soon there will be a video of the assembly on the model👉 https://www.youtube.com/channel/UCYPCHCvorQKBgTh_xUys0Og Thank you all Great seller, I recommend it

Buen Chasis 👍😁 Llegó muy rápidamente, como se especifica en la descripción, un Chasis muy agradable, bien hecho y bien embalado, llegó sin ningún golpe o falta de piezas. Sígueme en mi canal de Tubo DRRC Stunt, y pronto habrá un video del montaje en el modelo 👉 https://www.youtube.com/channel/UCYPCHCvorQKBgTh_xUys0Og Gracias a todos Gran vendedor, lo recomiendo

Realmente feliz con esta actualización, hace que el coche se sienta mucho más firme y robusto. La calidad de la misma es muy agradable, buena mano de obra. Aún no he salido a correr, pero todo parece prometedor. tiempo de envío fue genial también! Gracias BangGood!!!

Really happy with this upgrade, makes the car feel way more firm and sturdy. Quality of it is really nice, good workmanship. haven't gone for a run yet but all looks promising. shipping time was great too! thanks BangGood!!!

Realmente feliz con esta actualización, hace que el coche se sienta mucho más firme y robusto. La calidad de la misma es muy agradable, buena mano de obra. Aún no he salido a correr, pero todo parece prometedor. tiempo de envío fue genial también! Gracias BangGood!!!

nice .....good Qualität....

nice .....good Qualität....

nice .....good Qualität....

Не совподают расстояние по отверстиям( 2мм) на раме с оригиналом. В остольном неплохо.

Не совподают расстояние по отверстиям( 2мм) на раме с оригиналом. В остольном неплохо.

Не совподают расстояние по отверстиям( 2мм) на раме с оригиналом. В остольном неплохо.

This is URUAV, not JINGXI like photos...

This is URUAV, not JINGXI like photos...

This is URUAV, not JINGXI like photos...

Compra recomendada, es 90% compatible /, el único ajuste que se realizó fueron terminar los pre orificios que tiene para las barras de dirección en la placa. Es una compra que recomiendo ampliamente para el wltoys con chassis parecido, ya sea el a959, 969 y 979. Queda bastante bien además de la resistencia que ofrece por el precio WOW! la verdad.

Compra recomendada, es 90% compatible /, el único ajuste que se realizó fueron terminar los pre orificios que tiene para las barras de dirección en la placa. Es una compra que recomiendo ampliamente para el wltoys con chassis parecido, ya sea el a959, 969 y 979. Queda bastante bien además de la resistencia que ofrece por el precio WOW! la verdad.

Compra recomendada, es 90% compatible /, el único ajuste que se realizó fueron terminar los pre orificios que tiene para las barras de dirección en la placa. Es una compra que recomiendo ampliamente para el wltoys con chassis parecido, ya sea el a959, 969 y 979. Queda bastante bien además de la resistencia que ofrece por el precio WOW! la verdad.

if you really now what you are doing the hard work is definitely worth every penny

if you really now what you are doing the hard work is definitely worth every penny

if you really now what you are doing the hard work is definitely worth every penny

It was more work than i thought. For version B you have to drill 2 holes. -> For the steering. And the gears are free. It´s very good looking and stable.

It was more work than i thought. For version B you have to drill 2 holes. -> For the steering. And the gears are free. It´s very good looking and stable.

It was more work than i thought. For version B you have to drill 2 holes. -> For the steering. And the gears are free. It´s very good looking and stable.