pattarom
Q: Qual tamanho da área de corte? Tem como aumentar a área de corte?
Preguntado por BG531745838 sobre 2022-06-09 01:42:02
pattarom The working area is 400x410 mm and can be extended up to 850x410 mm with an optional extension kit (which can be purchased on the Atomstack website)
2022-06-10 12:34:20 Servicial (1)
pattarom As far as I know, someone has successfully cut 6 millimeters of plywood. It needs a lot of passes and a nozzle with compressed air that blows over the cut, otherwise, after a few passes, the wood starts to burn. Atomstack has recently started to sell his mini compressor that comes with adapters for all models of laser cutters and a cutting bed to place below the piece to cut to avoid burning the underneath table.
2022-04-27 07:30:51 Servicial (0)
pattarom No, it is a single channel.
2022-01-23 07:02:36 Servicial (0)Q: How can I get and restore the original firmware of this device
Preguntado por BG473341013 sobre 2022-01-11 08:47:29
pattarom You cannot restore original firmware without disassemble the plug invalidating the warranty. Also original firmware is not available for download.
2022-01-11 11:03:50 Servicial (0)
pattarom Yes, you can connect to Tuya App and you can connect from Internet to the device.
2021-12-08 01:22:34 Servicial (0)
pattarom Usually any NEMA 17 motor should run flawless. You only must check the connector pins position, because pins position is not a standard between manufaturers. If old motor is not burn, you can use a multimeter set in ohm measurement, to discover where motor coils are connected. To find a coil check what pins give continuity (or zero ohm). Compare the position of the old motor with the new one and modify the cable accordingly, changing the position of the wires in the connector. If the motor rotate in reverse, simply swap, between them, the wires of one of the coils (pratically invert the polarity of one of the two coils).
2021-11-13 02:20:29 Servicial (0)Q: Have you model with larger Engraving Size, for example 100cm * 100cm?
Preguntado por Bj Nas sobre 2021-10-02 09:41:40
pattarom Looking into manufacturer website, this is the only size their produce. Seems that all laser engraver models share same structure changing the features.
2021-10-04 01:36:56 Servicial (0)Q: where do I get the manual in English the download was in Chinese?
Preguntado por garryc sobre 2021-09-17 01:33:07
pattarom Included with the electronic load, there is a chinese and english manual.
2021-09-19 02:58:25 Servicial (2)
Q: Will this laser cut jigsaw puzzles?
Preguntado por BG441645121 sobre 2021-08-09 07:00:37
pattarom With the right drawings, you can cut any shape you want, even a jigsaw.
2021-08-10 03:45:02 Servicial (0)
pattarom You can adjust power to fit the material thru the software. There are no driver (if we not consider the driver for USB port). The engraver use GRBL standard, there are many program that you can use (for example the free LaserWeb). Istruction manual guide you to use a simplier software GRBL (yes program, protocol and firmware loaded into mainboard have the same name)
2021-07-22 02:29:28 Servicial (0)Q: Is it applicable for SMD PCB-s?
Preguntado por BG184861713 sobre 2021-05-27 02:58:37
pattarom Tecnically: yes. You can use a permanent marker to darken a blank PCB and then use the laser to clean the marker areas where copper must be eroded by acid. There are some videos on YT that show this process.
2021-05-27 10:59:47 Servicial (0)Q: is this efficient for outdoor measurmentjQuery111303441652662832677_1618152263573?
Preguntado por BG156151083 sobre 2021-04-11 09:45:29
pattarom PCB is exposed, so it isn't suitable to work outdoor. It must be protected from moisture, rain and extreme temperaures
2021-04-11 11:53:56 Servicial (0)¡Te invitamos sinceramente a suscribirte al correo electrónico de respuesta de invitación!
Si se suscribe, lo invitaremos por correo electrónico para que responda las preguntas que la gente tenga sobre los productos. ¡Al suscribirte, también ganarás la "Insignia útil "! Puede darse de baja en cualquier momento en la página de configuración de privacidad.
¡Ayuda a los demás y sé más feliz!
Thank you for subscribing! You have also earned a badge!
Thank you! Your answer will help ###name### and ###num### other people!
Check awaiting answers to see more people who need help.
Thank you! Your answer will help ###name### and ###num### other people!
Subscribe to "Invite Answer"emails and help others with product questions will earn you "Helpful Badge"!
We invite you to subscribe to our Invite Answer email!
Subscribe and you’ll be invited to answer product’s question by email, which will also earn you a "Helpful Badge"! You can cancel any time on the privacy settings page.
