Mejores ofertas para ROCHOBBY 1941 MB SCALER Coche RC Impermeable,16800 piezas de coche RC

David 12/08/2020

Ordered on the 24th June 2020 and delivered on the 12th August, which during the time of Corvid-19, I think wasn't too bad. The model was very well packaged and thankfully arrived unscathed in it's own suitcase..! I fitted my own receiver (PNP variant) and calibrated the throttle ok first attempt. The throttle was reversed on the tx stick though which reversing the throttle channel had no effect. The manual advises swapping the motor connections which was just a case of pulling apart connectors and swapping over. All then was ok. The plug from the headlights can be plugged into any spare rx channel. The model has a good level of detail in molded plastic that will need to be treated with respect. I fitted a 1/6th scale banggood military figure, set my throttle curve with a very flat middle section for sedate pull aways, set maximum end point steering travel, plugged in a 3s lipo and turned the model power switch on. A couple of beeps later and the headlights had a nice yellow glow, we were off... :-) Very smooth, torquey power delivery was immediately evident with a scale top speed of a slow jog pace, just right. The grippy soft tyres get great purchase on any obstacles and 58 degree entry angles make most slopes managable with ease. I ran an onboard lipo checker set to 3.6v per cell and managed an hour of sedate climbing and low throttle speeds without it going off on my 2200mah 3s pack. I checked and still had 33% power remaining. I noticed the suspension was quite hard and bouncing over bumps rather than soaking them up. On inspection, the shocks were set hard so I removed each upper securing allen bolt and shortened the shocks using their screw threads. Now the ride is much softer and realistic. I ran the car into near darkness and the headlights were very effective, beaming yellow over 4 feet ahead and were quite dazzling when heading towards me. Overall a great purchase that due to it's speed and intended use should last a very long time.

ROCHOBBY 1/6 2.4G 2CH 1941 MB SCALER Coche RC Impermeable Modelos de vehículos Control totalmente proporcional Sin transmisor receptor

US$373.99 US$407.99

4

Comentarios (0)

David 27/10/2021

A full front axial at the best price around, especially when using my accumulated discount points. The part arrived from China in good time but again my Banggood purchase was shipped and posted through my letterbox landing on a hard wooden floor packaged in only a thin polythene postal bag. Zero protection whatsoever. It looks like the part may have survived it's journey and fall but sorry, this standard of packaging is not good enough Banggood. I've yet to fit the new part to guarantee it's not bent or undamaged.

ROCHOBBY Font Bridge para 1/6 2.4G 2CH 1941 MB SCALER RC Coche Impermeable Modelos de vehículos Piezas

US$31.43 US$54.42

0

Comentarios (1)

Caja de engranajes de repuesto para excavadora RC Wltoys 16800 1/16 con motor cepillado 380 y piezas de modelos de automóviles 1440

US$30.02 US$31.99

Q: Can you confirm this item contains all the gears please, the description says it's the 'case'..? I have a broken final gear that connects to the output wheel and it looks like I need to buy the complete right hand side drive assembly. Thanks David Martin

Preguntado por David sobre 2021-04-17 11:36:41

Lacon This gearbox inside is with drive gearbox motor gear, steering gearbox two-stage gear, drive gearbox eight-stage reduction gear, drive gearbox output gear, steering gearbox three-stage clutch lower gear and steering gearbox three-stage clutch upper gear,do not have extra gears outside

2021-05-07 06:21:32 Servicial

Enviar

respuestas (1)

David 05/11/2020

Arrived in good time and the plastic case undamaged. For the money (the cost of just one quality HSS die), this is a good set for the hobbyist wanting to tap or thread soft materials like nylon, alloy etc, don't even think about cutting steel. I needed to re-tap the die holder securing screw hole straight away as the screw was fitted cross threaded on receipt. The hole cleaned out nicely though using the correct sized supplied tap and holder. It's a small metric tap and die set that I will use with care for years to come hopefully.