Flybear FXB17 Listo para volar 465 mm Envergadura 2.4Ghz 2CH Radio Control RC Modo avión 2 RTF
Una parte de la reseña se ha traducido automáticamente.
Este es un modelo a escala bastante bueno de un B-17 Flying Fortress. Por eso lo compré, ya que era mi intención pintarlo de forma más realista y modificarlo un poco para añadirle algo de realismo. Vuela muy bien y se ve muy bien en el aire. Aquí está una foto mía después de que lo jazzed un poco con un poco de pintura de plata y algunas marcas adicionales.
good plane but a bit expensive and has two motors and not 4 so don’t be fooled by the pictures. not like me anyway lol . recommend perfect for beginners.
Very simple, two channel differential thrust plane that required almost no assembly. All you do is glue on the fin, and a tube of glue is supplied for that purpose. There are also 3 wheels that plug into slots on the wings and fuselage, but you can fly without those, and they are easy to remove and refit. The inner two engines have motors fitted, but the outer ones are just dummies, but they have propellers that spin with the slipstream. The motors are 8x20 brushless which give more than enough power. The props rotate in opposite directions, and a spare of each type is supplied, as well as a 450mAh flight battery and a charger for the battery that plugs into a USB port. There are couple of problems you should fix or you will be disappointed. 1. The propellers are not a tight enough fit on the motor shafts, so as soon as you throttle up they will fly off. You can fix this y putting a piece of thread through the shaft hole on the propeller, which goes right through to the front. Then push the prop back on so the thread is trapped. It also doesn't hurt to wick a tiny amount of CA glue (superglue) through the front of the prop so it gets onto the shaft and the thread. Cut off any thread that sticks out using a modelling knife or razor blade. 2. The model won't climb, no matter how much throttle you apply, unless you do some work on the elevators to give it just a tiny bit of up elevator. About 2mm up at the trailing edge of each elevator is enough. First you need to cut away two tiny pieces of foam that join the elevators to the rest of the horizontal stabilizer and to the fuselage, so that the elevators become free to move. I used two tiny pieces of toothpick stuck into the fuselage to lift the elevators just enough, then a very small piece of sticky tape to hold them in position and stop them from moving in flight (see photo). With these changes, the plane will fly quite well. The gyro makes it very stable.
Gran modelo de avión! Vuela bien con 4 g de peso añadido en la nariz. Compré uno de nuevo. Pinté con pinturas de modelo acrílico para parecer más realista. Hay una vieja caja de cerillas B-17 G a escala 1/72 al lado.
gran producto y entrega a tiempo
Gran modelo de avión! Vuela bien con 4 g de peso añadido en la nariz. Compré uno de nuevo. Pinté con pinturas de modelo acrílico para parecer más realista. Hay una vieja caja de cerillas B-17 G a escala 1/72 al lado. He añadido los trenes de aterrizaje modificados.
Gran modelo de avión! Vuela bien con 4 g de peso addeg nariz.
¡Lim Ting dice que la cola de las moscas es pesada! cerciórese de que las hélices estén bien acopladas antes de ver cómo las hélices vuelan. puede eliminar las hélices fueraborda para un mejor vuelo silencioso apoyos fueraborda trabajo en los motores a bordo. También hay cortes para añadir un servo para el control del ascensor. Sin embargo la electrónica actual no soporta.
muy bonito avioncito
se ve bien y han llegado relativamente rápido