Comentarios de Clientes

4.95 fuera de 5
Escribe un Comentario
  • Todos los comentarios (110)
  • Imagen (3)
  • Video (4)
  • Todas Las Estrellas
    • Todas Las Estrellas(110)
    • 5 Estrellas(107)
    • 4 Estrellas(2)
    • 3 Estrellas(0)
    • 2 Estrellas(1)
    • 1 Estrellas(0)
Ordenar por:
Comentarios Recomendados
  • Comentarios Recomendados
  • Muy útil
  • Más Reciente
Reseñas solo de tu país (Honduras)
|
Mostrar original

Una parte de la reseña se ha traducido automáticamente.

  • 24/05/2017

    Получил через месяц в целости и сохранности. Описанию и заявленным характеристикам соответствует. Товаром доволен.

    Comentarios
    Mostrar original
  • 04/06/2017

    Riparazione eseguita con successo!!! La mia Mobius, a bordo del mio Drone ZMR250, a seguito di uno schianto non ha più dato segni di vita. Ma dopo aver sostituito la scheda interna passando dalla versione V6.7 all'attuale versione V6.8 tutto è tornato a funzionare. Ora è come nuova!

    Comentarios
    Mostrar original
  • 08/08/2016

    メイン基盤なので仕方が無いとは思いますが、値段が少し高いのが残念。レーサー機に搭載し、衝突等で破損し今現在二度目の基盤を交換しました。

    Comentarios
    Mostrar original
  • 14/09/2020

    trajo a mi Mobius ActionCam de vuelta a la vida y me encanta. Debería ser más barato ahora, he pedido uno nuevo por la mitad del precio.

    Comentarios
    Mostrar original
  • 27/06/2016

    I have a Mobius with the new V3 C2 Wide-Angle lens which I use for capturing HD FPV footage. Unfortunately the Mobius camera doesn't seem to hold-up too well to hard crashes: after only two crashes my Mobius stopped recording video no matter what SD card I used, or what firmware I flashed it with. So this product is a lifesaver! This PCB works with all Mobius cameras and takes only 5 minutes to install with a small screwdriver. Your Mobius will then work again good as new! I would recommend this product to everyone who flies FPV and uses a Mobius. You should at least have one (or two!) of these PCB's spare, even if your camera is currently fine; sooner or later the PCB will break in a crash and this will fix it straight away! Sooo much cheaper than buying a new camera! I ordered this from the EU warehouse on Saturday & received it on Monday in the UK with standard shipping! Well done Banggood!

    Comentarios
    Mostrar original
  • 09/09/2015

    When I ordered my Lens A Mobius direct from maker, I ordered the C lens extra. To my surprise it showed up with a spare case. So with a makeshift 180mAh Lipo and charge protector mini-pcb from an old spy camera and this replacement board I built a second camera even lighter than the first. Perfect for 5V powered FPV Camera. The small battery is good enough to power it up and initialise before powering the Vector FC which needs a steady Video signal at boot. Loaded latest firmware and its been faultless.

    Comentarios
    Mostrar original
  • 22/06/2015

    The mobius is good but its not indestructible so for the 2 mins it takes too replace this it has got to be the best solution and cheaper than buying a new mobius. It is the v3 model and i have updated to the latest firmware with out any problem. Thanks BG i can see myself needing another in the future.

    Comentarios
    Mostrar original
  • 11/04/2015

    Since i fryed my PCD when i experimented with a DIY TV Out FPV Cable (i put in ground and +5V backward) i ordered this and got the most recent Revision of the Board. Works like a charm now. Annotation: it has a high voltage protection, but if you power it backwards it will get damaged, and..... dont forget to take out the SD Card of your old PCB befor you trash it :p

    Comentarios
    Mostrar original
  • VIP3
    ES
    23/08/2018

    Me mandaron una mobius, que posiblemente por ser defectuosa me funcionó sólamente unas horas y de repente dejó de funcionar. les expliqué lo sucedido y me reembolsaron la cámara, con lo cual en lugar de ir a por una nueva, me limité a pedir un pcb de repuesto. Me llegó, la puse y funcionando perfectamente.

    Comentarios
    Mostrar original
  • 01/02/2018

    Replacement board ordered for a Mobius camera that had been fried by a faulty USB supply. Arrived quickly. Camera easily opened and board removed. Lens easily disconnected using the zif connector, however ALWAYS remove the battery first! Never disconnect the lens unit without disconnecting the battery first or in fact the same goes for a super-cap, remove that first. Re-assemble the camera affixing the battery with some double sided foam. Replace the two screws and then don't forget to load a SYSCFG file!

    Comentarios
    Mostrar original
Show:

    Total 0 paginas

    Ir a la pagina

    Puedes estar interesado

    recommendation for you
    • US$18.99
    • US$87.99
    • US$61.99
    • US$47.99
    • US$269.99
    • US$8.99
    • US$270.99
    • US$12.99
    • US$12.99
    • US$21.99
    • US$23.99
    • US$7.99
    • US$21.99
    • US$33.99
    • US$35.99
    • US$37.99
    • US$27.99
    • US$77.99