Mejores ofertas para Calentador de coche,Marco de carreras FPV,Motor sin escobillas

Calentador de Estacionamiento para Automóvil HCalory 12V 2KW/5-8KW con Control Remoto y Monitor LCD para Carros, Autocaravanas, Remolques, Camiones y Barcos

119,92€ 184,50€

Q: Does anyone know if these can be run laying on their side? I've got a couple of air vents in the wall of my little brick built workshop, and I could easily make a wall mount for one of these with the exhaust sticking straight through that, but it would be safer if the hot exhaust pipe went straight out horizontally rather than looping around below the unit and then out.

Preguntado por Reman sobre 2022-10-08 04:14:50

PiotrG nie zalecane jest ale jak już musisz to tak żeby świecą płomieniowa (żarowa) była u górze

2023-01-03 12:11:22 Servicial

Enviar

respuestas (1)

Reman 28/05/2018

It's not a light frame, Or notably stiff...... But just look at it, It's fri66in' adorable !!!! :) I built it up the day it arived. You'll need a Runcam Micro sized camera to go in the front as there's only 19mm between the side mounts. It'll take a 30.5 or 20mm stack, But headroom's a bit limited at 25mm between frame plates. With a micro VTX at the back, a 4 in 1 ESC and a small RX it's an easy build. I opted for an underslung battery on mine because the upswept blade tips on the iFlight Nazgul T3061's I'm using would get a bit too close to a top mounted battery for my liking. I've added a couple photos of the frame (Plus motors and props) fo scale. Ones next to my 220 Martian, And the other's with a full sized GoPro-A-like sitting on top, The others are of it finished (Without an FPV camera so far) with Racerstar BR1407 3500KV motors, A Racerstar 20A 4 in 1 ESC (Yeah, I know, It's a bit overkill for this, But I had it handy) an F3 omnibus FC, an Eachine VTX03, And a FlySky X6B RX. I've got one of the Eachine SpeedyBee CCD FPV cameras on the way to me for this to. I've also fitted one of the Realacc battery protection boards as I spend a few quid on Li-Po's and would rather not belly flop them into the ground without protection in an abrupt landing. As I said at the start, It's not a particularly stiff or light frame (The LT130 is probabbly a little better in both regards), But the finished quad is comically cute, and a fun addition to my Martian collection.

Realacc Martian II 140mm Envergadura del Eje 3mm Brazo Fibra de Carbono Kit de Bastidor de Carreras FPV

28,76€ 30,44€

6

Comentarios (1)

4X Racerstar 2507 BR2507S Edición Fire 1800KV Motor Brushless Para Drone RC y Frame de Carreras FPV

54,33€ 57,19€

Q: Does anyone think these would be OK to run on 3s with 7" props? With their lower KV I'm wondering if these could possibly be usable as cheap motors for a larger (But still reasonably light) framed build.

Preguntado por Reman sobre 2019-05-18 01:53:34

BG333840921 No the kv is too low . These are 5 to 6 s motors

2021-10-14 05:47:28 Servicial

Enviar

respuestas (1)

Kit de marco de carreras de fibra de carbono HSKRC XL5/6/7/8/9 232/283/294/360/390 mm para RC Drone

24,90€ 35,97€

Q: Will BangGood be selling the arms separately for this frame?

Preguntado por Reman sobre 2019-05-21 12:26:20

TDFPV why don't you just buy multiple kits. theyre so cheap....

2020-08-14 02:21:54 Servicial (1)

Enviar

respuestas (4)

Reman 20/06/2019

So very pretty. The colours within it shift all over the spectrum as you turn it in the light.

6cm cristal iridiscente pirámide prisma Color del arco iris decoración del hogar FengShui Reiki decoraciones curativas

20,29€ 22,13€

1

Comentarios (1)

Reman 22/10/2018

I managed to grind down one of the "Pivot center pins" to make this fit my chuck, But my guess is that this is more for an industrial setting. I only bought this because I have a mystery chuck on one of my drills and couldn't be bothered to try to work out what size replacment key I needed. After the tweaking it's working fine though.

4 Way Drill Press Chuck Key Universal Combination Hand 3/8 1/2 3/4 1 Inch Chuck Key

8,44€ 16,16€

0

Comentarios (1)

Reman 22/10/2018

This isn't particularly bad vice, But it's definitely made to a price. I needed to remove casting flashing from several places before it would sit flat on my pillar drill (Less than a minutes work with a Dremel), But now that's done it works well. It's distinctly "Light duty", But that was expected at this price point. If you need a cheap vice for a hobby or "Jewelers" pillar drill then this could be a contender

Tornillos de prensa de taladro Abrazadera Reparación de máquina mecánica de mesa de banco herramienta DIY Rectificado

23,43€ 24,90€

2

Comentarios (0)

Eachine Bat 19S 1 / 1.8 "Starlight CCD 800TVL 2.1mm / 2.3mm 16: 9/4: 3 OSD conmutable PAL / NTSC FPV Cámara Rojo / Negro para RC Drone

24,49€ 32,10€

Q: Is this a CCD or CMOS camera? Also, Is the lens fitting an M12 thread, rather than the M8 thread that most other 19X19mm FPV cameras use?

Preguntado por Reman sobre 2019-07-08 03:10:59

BG_AFF I dont know.sorry

2019-07-25 09:26:10 Servicial (2)

Enviar

respuestas (9)

Reman 05/03/2020

Quite a nice set. A good selection of pin counts and spacings. A bit thick for some locks, but still worth having for the times you CAN use them to quickly bypass the locks with less restrictive keyways.

DANIU 7pcs Peine Recoger Herramienta de Bloqueo de Acero Inoxidable Herramienta de Cerrajero para Selecciones de Casa

5,53€ 10,14€

2

Comentarios (0)

Reman 15/02/2020

My set arrived with more than half of the pick blades slightly bent or curved. Some of the blades have smears of a black tar like substance on them, and when straightening the blades out they felt a bit too "Pliable" for my liking (rather than springy). That said, It's not a ridiculously bad starter set. With the addition of a few comb picks it would make a reasonable set for a hobbyist to play with and work out which picks they use most, then buy better quality versions of those at a later date.

DANIU 24Unids Lock Pick Set de Solo Gancho Herramientas para Cerrajería Lock Pick Kit

18,10€ 19,36€

0

Comentarios (1)

Reman 15/02/2020

Not a bad set. There's a few other styles of pick I'd have liked to have seen included in the set (like maybe a couple more rake picks), but as a basic kit its not bad. The blades feel reasonably springy, so they're less likely to bend or break than others I've played with, and the quality seems pretty good. The sleeve grip bits were a bit of a pig to fit until I warmed them up a bit with a hairdryer.

DANIU 12Pcs Juego de herramientas de ganzúas Abrepuertas Kit de herramientas de cerrajero Varios candados transparentes Combinación de cerraduras Conjunto de herramientas de cerrajero

25,56€ 23,98€

0

Comentarios (0)

Reman 20/06/2019

Mine turned up with a fairly big chip out of the edge that extended about a 5th of the way down one side. It refracts sunlight all over the window sill it's sat on, So it's still quite a pretty effect, But it's a bit of a shame that it's got such a large chip out of it. :(

30x30mm Cube Defectuoso Cross Dicroic Prism RGB Combiner Splitter Glass Decor

19,27€ 21,21€

6

Comentarios (0)

Reman 09/01/2020

It's mostly made out of aluminium, Even the sliding dovetails are alloy (With a brass gib), So I doubt this is going to last forever, And it's design seems to have been thought out so as to make it by using the least amount of material as possible. It also uses normal screw threads on the lead screws rather than acme threads ............ BUT, if you understand that you're not going to turn a flimsy little 100080 mini drill press into a high precision baby manual milling machine with this It's actually quite a useful little accessory. It's really handy on a drill press for small projects that need reasonably precisely groups of holes drilling. You can clamp the workpiece down and use the dials on the handles to move the work the required distance to the next hole (As long as you keep going the same direction. Mine has about half a turn of backlash). it saves a fare bit of time marking out before hand. The gibs can easily be tightened up until the beds unmovable, but if you're careful you can pinch them up just enough that it's still pretty free moving, but has next to no play in it. It may have been built to a budget, But that doesn't necessarily mean it's been built badly. I'm pretty blown away by it's value. I think with a few tweeks it could possibly even be used with my large angle block as a poor man's milling slide on my lathe.

MINIQ BG6300 Mini Precision Fresadora Worktable Multifunction Drill Vise Fixture Working Table

52,51€ 85,78€

0

Comentarios (0)

Reman 08/10/2018

Less thrust than the 6045 bullnose triblade props I usually use, But a LOT more flight duration, And really quiet too..

2 pares de Emax AVAN Long Range 6 pulgadas 6038 6X3.8X2 Hélice de color negro CW CCW para RC Drone

9,58€ 10,14€

1

Comentarios (0)

Reman 22/04/2019

Not stainless steel, But works fine and can be fitted without dismantling the shower pole.

Jabonera Ajustable Riel de Ducha Deslizante Platos de Jabón Almacenamiento Suave Baño Soporte

10,65€ 11,06€

0

Comentarios (0)

Reman 27/05/2018

This is probably going to sound stupid, But I only bought this because ages back I accidentally ordered a load of 75mm blades and wanted something I could use them on. :) As a bonus, it flies really well for a larger brushed quad, And can really hustle about when you want it to. It's a pretty strong frame to

Fibra de carbono de 120 mm DIY Micro Mini FPV Cuadricóptero Kit de bastidor Grosor de 2 mm 8.5x20 mm Coreless motor

9,95€

4

Comentarios (1)

Orgone Pyramid Generador de energía Torre de sanación Cristal Rojo Piedra preciosa Decoraciones para el hogar

17,04€ 18,44€

Q: It's made out of resin, not crystal.

Preguntado por Reman sobre 2019-07-06 05:54:26

Enviar

respuestas (0)

Reman 22/04/2019

For the pr ice I wasn't really expecting these to be up to much (I've seen DIY bare 18650 torch body's that co st more than these !)......... But I'm VERY pleasantly surprised ! The machining feels reasonably good and both of the ones I've bought work as expected. Light output is easily good enough for spotting my dogs when they're hiding right down the garden, And being zoomable as well as micro USB chargeable makes them very a very convenient torch to own. Being able to charge them from a phone charger also means they would be useful as an emergency torch to put in the cars glovebox. So far they seem well worth the mo ney.

XANES® 1123A T6 LED 5 modos Zoom telescópico USB recargable Linterna 18650

9,85€ 14,78€

0

Comentarios (0)

Bienvenido a Banggood,

Usted permite:

Todos los mensajes

Usted es el experto, ¿puede ayudarme?

Sobre insignias

About Badges

Helpful Badges

Are you ready to help?