Mejores ofertas para Impresora 3D,LED,Batería de lipo

Dovcharov 08/12/2020

Amazing housing for my 3d printer. now my ABS prints are ok. Also reduces noise. you will need a cable extension kit for this housing to keep the control block outside. Also a number of tweaks are required, since your stepper motors may start to overheat. I tuned down the current on my Y and E axes to keep my motors cooler (vref tuned down to 0.6 vs original 0.75), and I plan to replace my printer mobo to SKR MINI E3 2.0 with quiet and cold TMC2209 stepper drivers

Recinto de gran tamaño Creality 3D® para impresora 3D Ender-5/5 pro/5 plus/CR-10Pro/10 V2, con papel de aluminio ignífugo

US$143.21 US$148.99

2

Comentarios (0)

Dovcharov 09/06/2020

If you need to pass through the LED strip signal from the flight controller to the BEC board, solder the small "L" jumper near the DIN/S pad, and cut off the top of the mode selection button on the BEC board. "L" jumper connects the DIN\S pad to control wires of led strips, and broken mode button stops output of internal PWM generator of the BEC board. Obviously, after such change you will only be able to control the connected LED strips via the flight controller. "P" jumper works another way. When it is soldered, the PWM signal of internal led strip signal generator of the BEC board outputs through DIN/S pad as well. So you may control additional LED strips from one LED board.

LANTIANRC WS2812 Tira de luz LED 20 Lámparas 5V 0.23A Módulo de tablero de control para RC FPV Carreras Drone Vuelo nocturno

US$5.21 US$7.82

4

Comentarios (0)

Dovcharov 23/06/2020

Good battery, but does not fit Mobula 7 HD battery tray. Too thick. My mistake, unfortunately.

Batería Lipo de 11.4V 300mAh 80C 3S con Conector XT30 Gaoneng GNB para URUAV UR85/UR85HD Mobula7 HD Sailfly-X RC Drone

US$16.16 US$16.99

0

Comentarios (0)

Dovcharov 09/06/2020

Great slim props for 6s racing drone.

2 pares Gemfan Hurricane 51466 5 Inch Soporte de hélice de 3 cuchillas duradero POPO para RC Drone FPV Racing

US$8.07 US$8.99

0

Comentarios (0)

Dovcharov Buyan iFlight mod for your DJI FPV goggles, and install Rapidfire module into them.

shrekowski 12/09/2019

Wow just would like to say Dogital FPV it is amazing , Is like to change CRT tv to LCD... From now HDO with rapidfire and crossfire will collect dust.

Combo Gafas DJI Digital FPV System Air Unit 5.8GHz 8CH Transmisor de 1080P Cámara HD 1440X810 con Control Remoto Modo 2 Súper baja latencia para Dron de Carreras RC

US$967.49 US$1,289.99

8

Comentarios (2)

ZOHD Talon GT Rebelde 1000 mm Envergadura V-Cola BEPP FPV Avión RC Avión de vuelo Ala PNP

US$308.99 US$370.79

Q: отзыв написать не могу пишу сюда,после 1 минуты работы на полном газу в моторе отклеялось половина магнитов,)что-то первый раз такое встречаю))))

Preguntado por Luxss sobre 2019-08-10 05:20:55

Dovcharov Да, штатный мотор - шлак. Бери на замену SunnySky X2216 2й или 3й версии 1250KV. У меня пока родной мотор от Талона работает, магниты на месте. Но мне видимо повезло.

2019-10-24 01:59:46 Servicial

Enviar

respuestas (1)

Dovcharov 11/06/2018

This is a nice frame light and solid. Good looks. The front "canopy" fits Runcam Micro Eagle camera just fine. The only drawback I found is that frontal horizontal standoff comes with M3 thread however all the screws and holes in frame are M2. So front horizontal standoff needs to be replaced or holes in carbon fiber need to be drilled for M3 screws. Please note that stack mount holes are also M2 and motor mounts are for 11xx motors. You can use 20xx or 23xx props with this frame.