Todos los mensajes

georget 22/09/2019
I purchased the Enusic battery charger mainly because I wanted to experiment with the Pulse Repair mode. The idea is that it will send low and high frequency pulses into the battery and help break down the sulfate that builds up on the plates over time. This sulfate build up can weaken a battery so removing it sounds good to me. I have used the Pulse repair on several batteries. It may take several hours depending on size and condition of battery, but eventually the Pulse repair will finish and turn OFF. If I wait a few minutes, and try the Pulse repair again on the same battery, it will run for a few seconds, then turn OFF so it must have done something that the charger can measure. Very cool! This charger has an internal fan that turns on when in Pulse repair mode. In the video, I use an oscilloscope to show what the output of the charger looks like when in Pulse Repair mode and disconnected from the battery. The voltage level shifts between 8 volts and 14 volts every second. It also has 25 kilohertz high frequency pulses measured from rising edge to rising edge. When the charger is connected to a battery that is already charged, you will not see the voltage level shift down to 8 volts on the oscilloscope. You will still see the 25 kilohertz high frequency pulses. The charger has a LCD display that shows voltage, current, and percentage of charge in the battery. It also has a motorcycle mode that limits the current to 1.5 amps. In the normal Vehicle mode, the current has a max of 8 amps. As the battery charges up, you can watch as the current draw goes down. When the battery is fully charged, it switches to OFF. So far, I like this charger a lot. If you have any experience with it, please add your comments to my YouTube video below... https://youtu.be/TLdoGV_QEuY
33
Recomendaciones
Comentarios (2)

sam https://www.banggood.com/Wholesale-Maintenance-Fixture-c-7844.html?akmClientCountry=CN&from=nav

2019-11-12 09:33:34 Servicial (1)
Enviar
respuestas (2)

Q: is this compatible to nissan navara np***** model?

Preguntado por BG036491347 sobre 2021-09-09 10:20:06

georget Does the 2017 Nissan Navara np300 have a OBD2 connector?

2021-09-09 12:32:11 Servicial (0)
Enviar
respuestas (1)

Q: is this compatible for Toyota vios 2005?

Preguntado por BG314474717 sobre 2021-08-25 02:17:59

georget Does your 2005 Toyota Vios have a OBD2 connector?

2021-08-25 07:17:54 Servicial (0)
Enviar
respuestas (3)

Q: does this model supports 99 Toyota camry?

Preguntado por BG536171144 sobre 2021-05-16 02:27:02

georget If your car has a OBD2 port, the scanner should be able to read some data.

2021-05-16 04:39:09 Servicial (0)
Enviar
respuestas (4)

Q: What is the weight of the box

Preguntado por silvabryan960 sobre 2019-11-19 11:42:36

georget Sorry

2021-04-08 08:38:20 Servicial (0)
Enviar
respuestas (2)

Q: is it have one colour

Preguntado por Murali Kp murali sobre 2019-03-30 01:49:53

georget These are RGB LEDs so you can change the color.

2021-04-08 08:35:53 Servicial (0)
Enviar
respuestas (4)

Q: how about weight?

Preguntado por incxbxs sobre 2018-11-23 05:52:44

georget The weight of the device is only around 1 pound US since it is made of hollow plastic. You may want to add weight to the base for a more stable device.

2021-04-01 08:21:21 Servicial (0)
Enviar
respuestas (6)

Q: Does it have inner mounting holes for placing pcb inside?

Preguntado por Vitocolr sobre 2018-02-19 03:43:49

georget Yes see customer photos.

2021-04-01 08:16:42 Servicial (0)
Enviar
respuestas (2)

Q: Theo power suply its inclused?

Preguntado por Catulo sobre 2021-03-31 07:24:39

georget 12V Adapter NOT included

2021-04-01 08:14:47 Servicial (1)
Enviar
respuestas (1)

Q: Does this unit work on Chinese Saic mg6?

Preguntado por MSRAHBI sobre 2021-03-30 01:15:24

georget In 2008, the OBD2 standard became mandatory for all vehicles produced for the Chinese market.

2021-03-30 06:29:44 Servicial (0)
Enviar
respuestas (1)

Q: How to get the product responsive? In Q

Preguntado por ericluiijf sobre 2020-04-14 10:18:44

georget Connect Arduino to computer using USB cable and then run the Arduino IDE software.

2021-03-25 07:18:08 Servicial (0)
Enviar
respuestas (4)

georget For three dollars, it probably does not have too much noise suppression inside. Give it a try and let us know.

2021-03-25 07:15:04 Servicial (0)
Enviar
respuestas (2)