Thack
Q: Are the valve springs both the same size/gage of wire, can not get it to run
Preguntado por themckenneys sobre 2019-05-08 11:20:36
Thack Yes, they are, but the exhaust valve spring has been stretched longer, so it applies more force when installed. You want the shortest spring on the inlet valve.
2019-05-11 05:13:04 Servicial (0)
Thack You connect it the the engine chassis - it's the ground return for the spark. However, even when connected you will probably find the Hall effect sensor soon fails - the ignition unit creates high voltage spikes across it.
2019-05-11 05:12:08 Servicial (1)Q: How is oil applied to the piston, piston rings, and cylinder?
Preguntado por CNR6400 sobre 2018-09-12 09:21:19
Thack I run mine on a 50:1 gasoline / two-stroke oil mix. Don't forget to lubricate the little end bearing occasionally - it is a plain bush bearing with no oil feed.
2019-05-11 05:10:51 Servicial (1)Q: this engine does run or not?
Preguntado por kanzezol sobre 2018-11-07 03:54:39
Thack The engine will run as received. However it has many design faults which preclude it from running reliably for a long time. For example, the ignition unit keeps destroying the Hall effect sensor with high voltage spikes. Also the ignition unit fails frequently. I ordered three more spare units, and out of the four (three plus the original), three of them have failed. In the end I fitted an ignition unit from a British maker. The big end bearing is aluminium on steel, which would normally be OK but the steel big end journal is very rough, not smoothly ground, so it wears away the aluminium connecting rod very quickly. The valves and valve seats are both brass, so will probably have a fairly short life. IMPORTANT: the valve seats are a loose fit in the cylinder head! They are held in place with some kind of flexible sealant (silicone?). I've had one come loose, and the valve seat jammed the inlet valve open. The piston hit the valve and stopped the engine. The main bearings are rollers with no inner race - the rollers run directly on the crankshaft. If the crankshaft had been smoothly ground that would be fine, but it isn't - it's rough, so the main bearings make a LOT of noise. Also, on mine the main bearing caps were loose - the screws had barely been nipped up. When I tightened them even slightly the engine wouldn't run due to excessive friction. The main bearings had not been correctly line bored. When running on gasoline with a load for a
2019-05-11 05:03:32 Servicial (3)Q: where can I get a new spark plug
Preguntado por Jim sobre 2018-07-29 03:37:41
Thack The spark plug that came with mine is definitely not 1/4-32. The thread is M8. I had to make an adapter to fit a 1/4-32 spark plug.
2019-05-11 04:49:46 Servicial (0)Q: Hi, Which kind of signal this devive produces, Best wishes HPu
Preguntado por putko sobre 2018-03-20 01:52:57
Thack Most of the replies have been incredibly unhelpful. As far as I can see it's an adjustable constant current source in the 4-20mA range, although the description is so confusing I might be wrong.
2018-07-09 08:32:34 Servicial (0)
¡Te invitamos sinceramente a suscribirte al correo electrónico de respuesta de invitación!
Si se suscribe, lo invitaremos por correo electrónico para que responda las preguntas que la gente tenga sobre los productos. ¡Al suscribirte, también ganarás la "Insignia útil "! Puede darse de baja en cualquier momento en la página de configuración de privacidad.
¡Ayuda a los demás y sé más feliz!
Thank you for subscribing! You have also earned a badge!
Thank you! Your answer will help ###name### and ###num### other people!
Check awaiting answers to see more people who need help.
Thank you! Your answer will help ###name### and ###num### other people!
Subscribe to "Invite Answer"emails and help others with product questions will earn you "Helpful Badge"!
We invite you to subscribe to our Invite Answer email!
Subscribe and you’ll be invited to answer product’s question by email, which will also earn you a "Helpful Badge"! You can cancel any time on the privacy settings page.
