Todos los mensajes

Q: cuánto alcance tiene?

Preguntado por BG411141793 sobre 2021-10-18 03:39:44

simole88 You are probably new to this hobby, because this is the value that is given the most importance. If you are referring to the maximum distance you can go away with your model before losing the signal (fail-safe), unfortunately you must know that there is no precise boundary. The distance is influenced by any interference from electronic devices present in your flight area, by air humidity, by a value of RF freq. fine tune not set correctly, by the receiver you have chosen and by the positioning of the antennas. In any case it is a small radio but it is certainly sufficient to fly indoor or in sight with your drone, plane or RC-Model. I do not recommend adding a crossfire module, even if supported, because battery 1S 18650 Li-ion will not be enough to give power to everything

2021-10-20 12:01:50 Servicial (0)
Enviar
respuestas (0)

Q: Hello there. Can I install a different motor on this bench? Does it work.

Preguntado por tamtam55 sobre 2021-07-29 01:22:40

simole88 Yes you can install a different motor or even a leser module. If you have a 3D printer you can also print the various adapters according to your needs. Online you will find many tutorials and project already done...

2021-10-20 10:52:57 Servicial (0)
Enviar
respuestas (0)

Q: what receiver for an adfs-2a transmitter, say flysky i6s

Preguntado por mgamba sobre 2019-09-16 05:06:50

simole88 Forgive me, but I don't understand what your question is. I don't know about the adfs-2a protocol. I know the Flysky i6S Radio transmitter which works with the AFHDS-2A protocol. This tiny receiver works with DSM2 protocol that isn't compatible with Flysky Radio unless you are using an external multi-protocol module.... If you are looking for a nano receiver like this to bind with your Flysky i6S Radio transmitter, you have to choose "Flysky FS2A 4CH AFHDS 2A mini compatible receiver PWM"

2021-10-11 07:34:02 Servicial (0)
Enviar
respuestas (1)

simole88 Hi, you'll need to select and upload on the "FMS Reflex Gyro System V2 flight controller" the right model everytime. It isn't the same profile for all three because the model (CG, aerodynamic and flying spec.) are different..

2021-10-11 06:28:31 Servicial (0)
Enviar
respuestas (1)

Q: Please, still not available in CZ warehouse ?

Preguntado por pidi52 sobre 2021-10-08 02:36:20

simole88 At the moment it is only available at the CN warehouse. Maybe contact Bangood customer service for more information

2021-10-11 05:19:11 Servicial (0)
Enviar
respuestas (1)

simole88 No, this receiver works only with FrSky D16 (or D8) protocol. Alternatively you can bind it with a multi-protocol radio like these: Radiomaster TX16S, Jumper T8SG, Eachine TX16S, Jumper T-Lite, Jumper T18 or T18 PRO, Jumper T12 ... Or an external multi-proticol module compatible with your Radio transmitter if supported...

2021-10-03 11:28:23 Servicial (0)
Enviar
respuestas (1)

Q: What is the lowest current that can be set up?

Preguntado por Vlad sobre 2021-10-02 07:43:29

simole88 min. current that can be set up: 1A with resolution of 0.05A

2021-10-03 10:53:47 Servicial (1)
Enviar
respuestas (1)

Q: does it fit Sunbird v2.0 upgrade

Preguntado por HampusH sobre 2021-09-22 09:32:31

simole88 Hi, if you use a 3S lipo and 20A ESC, I suggest to work with 8-10 inch prop. If you use the recommended electronic, the MM2212 1100KV motor supports the following propeller: 8x4.3, 9x4.7 and 10x4.7. I do not recommend the 10x4" prop because it is excessive and requires too much power (@ 12.6 V > 17.5A > 220W > and a thrust of 750g). This foldable propeller of ASW28 is not recommended because it is a 10x6" prop..

2021-10-03 09:11:37 Servicial (0)
Enviar
respuestas (1)

simole88 Youcan turn the led strip ON and OFF from a physical switch (light switch) or a Wi-Fi switch. From a physical switch, however, if the LED is turn off you will not be able to turn it ON from the application on your mobile phone or google or alexa...

2021-09-26 10:01:12 Servicial (0)
Enviar
respuestas (1)

Q: I got dx7s and it would not bind , dsm? Or dose it hafe to be dsm2?

Preguntado por ozzieocat sobre 2020-01-21 08:52:39

simole88 Testedand works fine with DSM2 protocol on my Radiomaster TX16S

2021-09-26 09:53:12 Servicial (0)
Enviar
respuestas (1)

Q: Can I use this giro with my FMS 1400 j3 Cub to control ground looping?

Preguntado por Paul sobre 2021-08-02 08:41:45

simole88 Yes,FMS 1400mm J3 Club V4 is supported by FMS Reflex Param V2.0 You can load the model and control it from the gyro safely! I hope I was helpful

2021-09-26 09:47:24 Servicial (0)
Enviar
respuestas (1)

simole88 Yes, this tiny receiver (22×12mm) have an ESC output (M+ and M-) for tiny BRUSHED motor like 410 or 412 brushed motor. Also has two outputs for two micro magnetic servos (included). You can connect il to its connector ( tiny 2pin connector) or solder the cable directly. Good flight!!!!

2021-09-18 05:55:10 Servicial (0)
Enviar
respuestas (1)

simole88 This Battery: Uruav 1300mAh 80-160C 4S (14.8V ~19.2Wh) have a weight of 156g and real size of 34,4×28,9×73,3mm. - Balancing wire + connector have a length of 63mm (22AWG silicone wire cable) - XT60 connector + wire have a length of 130mm (10AWG high quality silicone wire cable)

2021-09-18 05:13:45 Servicial (0)
Enviar
respuestas (1)

Q: does this fit the radiomaster tx18 as well.thks

Preguntado por BG401622911 sobre 2021-07-06 08:21:52

simole88 I have no idea, you could first disassemble the TX18 and check if the image of this antenna corresponds to the one mounted on yours Radio. In that case I think they are compatible, since the transmission frequency of the two radios is always the same.

2021-09-15 05:38:34 Servicial (0)
Enviar
respuestas (1)

simole88 I've bind this receiver with my multi p. Radiomaster TX16S: --> Internal module --> FrSky --> D8 and it works fine. With the new FrSky Radio (QX7s and newest) you can update and choose international firmware (FCC) or EU firmware (LBT) I think it's no way to update to D16.... And in this receiver you haven't possibility to connect it to your Radio or PC or download and update internal firmware.

2021-09-15 05:33:23 Servicial (0)
Enviar
respuestas (1)

simole88 Nella descrizione del prodotto sono riportati tutti i modelli che questo dispositivo "Universal 280-868 MHz Garage Door.." è in grado di copiare. Assicurati che il telecomando che stai per copiare sia Master e non Slave. Master: premendo un tasto qualsiasi del telecomando da copiare, il led lampeggia e poi diventa stabile. Slave: premendo un pulsante qualsiasi il led è subito fisso. Spero di esserti stato utile

2021-09-15 05:09:31 Servicial (0)
Enviar
respuestas (1)